Faulhaber 3242 BX4 Series Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 52

background image

39

4 Functional Description

4.4 Motor with SC speed controller

PWM mode of the power output stage

If U

nsoll

is specified as the voltage at the motor it is operated with speed control. The speed is control-

led by pulse width modulation (PWM), i.e. the motor tries to achieve a constant speed under fluctu-
ating load.
Due to the technical requirements of the motor with SC speed controller, assuming the allowable
maximum housing temperature is adhered to, the maximum possible continuous torque in PWM
mode may be lower than under full control. The maximum thermally allowable continuous current
reduces accordingly.

4.4.2 Configuration

The control parameters of the speed controller integrated in the motor can be individually adjusted
to the respective application via a PC. This requires a programming adapter which can be ordered
separately as well as a version of the FAULHABER Motion Manager PC software suitable for the
speed controller.
The software is available on request or on FAULHABER’s internet site
(

http://www.faulhaber.com/MotionManager

).

CAUTION!

Risk of damage

Before starting up, check the parameters configured in the control and if necessary adjust to the con-
nected motor. Incorrectly set values can cause fatal damage to the motor and/or the speed controller.
In particular, the following parameters must be correctly set:

Duration and maximum current value,

controller parameter.

The servomotor is equipped with digital Hall sensors, with which the commutation signals can be
determined. The actual speed value is determined via the time interval between the edges of the
Hall sensor signals.

Preset default basic parameters:

Due to the resolution of the digital Hall sensors, speeds from approx. 400 rpm can be stably con-
trolled.

PWM frequency at the power output stage: approx. 96 kHz.

2-quadrant operation with function for quick speed reduction: The motor windings are short-
circuited for faster transition from higher to lower speeds.

«
...
37
38
39
40
41
...
»

Содержание 3242 BX4 Series





















































Отзывы:

Нет отзывов

Похожие инструкции для 3242 BX4 Series

BA-Intellidrive BAI 10

Бренд: Aerotech Страницы: 202

Бренд: REDEX ANDANTEX Страницы: 28

Бренд: NEC Страницы: 14

Бренд: ABB Страницы: 20

Бренд: Eskridge Страницы: 7

Бренд: Targus Страницы: 4

Бренд: Leadshine Страницы: 19

Бренд: Leadshine Страницы: 17

Бренд: Leadshine Страницы: 22

Бренд: Leadshine Страницы: 57

Бренд: Leadshine Technology Страницы: 17

Бренд: Leadshine Страницы: 70

Бренд: Pacific Scientific Страницы: 58

Бренд: BFT Страницы: 32

Бренд: LinMot Страницы: 33

KFUtronic Series

Бренд: Küenle Страницы: 74

Бренд: SMS Страницы: 75

Бренд: Texas Instruments Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды