Faulhaber 3242 BX4 Series Скачать руководство пользователя страница 48

Страница: 48 / 52

5 Operation

5.1 Commissioning

Before starting up the servomotor together with a mechanism, the following points must be
checked:

The motor has been installed according to the specifications.

The ribbon cable of the motor is connected according to the requirements (risk of polarity rever-
sal!) and is laid so that it cannot be damaged during operation. The maximum load values must
be noted and observed. See

Chapter 1.4 “Ambient conditions”

Lengthening the connection leads can affect the function and properties with respect to EMC. All
connection leads may not exceed a length of 3 m.

The connected mechanism is installed free of blockages.

The loads and stresses on the shaft (axial, radial and torques) are within the specified values.

CAUTION!

Risk of injuries

A risk of injuries can result from protruding rotating or moving parts of the driven mechanism.

Cover rotating and moving parts with appropriate devices.

CAUTION!

Risk of burns

Depending on the load and ambient temperature, very high temperatures can occur on the surface
of the unit.

Contact protection (guards) must be provided if necessary.

Содержание 3242 BX4 Series





















































Результаты поиска

Содержание 3242 BX4 Series

Отзывы:

Похожие инструкции для 3242 BX4 Series

Бренды по названию

Популярные бренды

Faulhaber 3242 BX4 Series, Инструкция по эксплуатации

Результаты поиска

Содержание 3242 BX4 Series

Отзывы:

Похожие инструкции для 3242 BX4 Series

Бренды по названию

Популярные бренды