Fast 9553P страница 79 Скачать руководство пользователя

Страница: 79 / 87

SERVICE

SERVICE

3PT Sprayer 9553P / 9573P

Page 79

Aligning Booms

The booms  on  each machine  are  designed
with  set  screw  adjustments  that  provide  a
method to adjust for straightness. By keeping
the  booms  straight, the sprayer  produces  a
consistent clearance to the crop.

1. Place the machine in its field

configuration with the boom at a
comfortable working height.

2. Place all controls in neutral, stop the

engine, set the parking brake,
remove the ignition key, and wait for
all moving parts to stop before
continuing.

3. Loosen the position bolt jam nut(s) at

the hinge.

4. Turn the position bolt(s) to the

required position.

5. Sight along the boom to be sure it is

straight (level) at each hinge.

6. Tighten the fasteners.
7. Repeat as necessary.

Figure 22: Inner boom

Figure 23: Outer boom

Содержание 9553P
























































































Результаты поиска

Содержание 9553P

Отзывы:

Похожие инструкции для 9553P

Бренды по названию

Популярные бренды

Fast 9553P, Руководство пользователя

Результаты поиска

Содержание 9553P

Отзывы:

Похожие инструкции для 9553P

Бренды по названию

Популярные бренды