background image

 

 
 
 
 

OPTIONS

 

 

REFERENCE FENCE ATTACHMENT

 

 
The  reference  fence  attachment  provides  the  operator  with  an  adjustable  material  stop  for 
cutting uniform lengths.  It can be set out to a maximum of approx. 4 feet. 

  
ASSEMBLY 

 
Bolt  the  fence  bracket  to  the  end  of  the  steel  bar  using  the  bolt  included  with  the  bracket.  
Next,  slide  the  bar  through  the  holder  rings  on  the  machine  frame  from  the  LEFT  side.  
Tighten the thumb screw on the holder after adjusting for desired length.  
 

 
 
 
 
 

FOOT PEDAL CONTROL 

 

                                                                     
The  Foot  Pedal  comes  fully  assembled  and  pre-
wired. It can be plugged in at any time.  
 
A jack is provided on the underside of the electric 
box.  Push  the  plug  into  the  jack  until  it  locks  in 
place. To remove, just push the release button on 
the jack.

  

 

When  the  foot  pedal  is  plugged  in,  both  the  push 
button  on  the  machine  and  the  foot  pedal  will 
control the machine.

  

 
 

Note: 

Extra  caution  must  be  observed  when  using  the  foot  pedal  to 
keep fingers away from cutting blades.

  

 

Never: 

Have  one  person  work  the  foot  pedal  or  push  button  while 
another is feeding rebar into the machine.

  

 

Содержание FC-800













Отзывы: