manualshive.com logo in svg

Farymann Diesel 15W Series, Руководство по ремонту, Страница: 77 / 80

Поделиться
Скачать
Farymann Diesel 15W Series Скачать руководство пользователя страница 77

TROUBLESHOOTING

- 77 -

8.4  Poor engine performance and/or black smoke

Dirty engine

Dirty air filter.
Excessive oil carbon deposits on
piston and cylinder head.

Clean / renew filter.
Decoke components / change vent
valve.

General Engine Condition

Worn piston rings.
Worn piston and cylinder.
Worn bearing.

Renew rings / check air filter.
Overhaul engine.
Overhaul engine.

8.5  Imperfect operating behaviour

Overheating

Engine overloaded.
Cooling fins dirty.
Cool air intake obstructed.
Short circuit of cooling air.

Oil level in crankcase is too high.
Faulty injector nozzle.

Reduce load.
Clean cooling fins.
Remove obstruction.
Improve cooling air flow (check
engine installation).
Drain to proper level.
Check / repair / renew nozzle.

Knocking Noises

Oil carbon deposits on piston.
Injector needle sticking.
Advanced ignition.
Broken piston rings.
Worn piston and cylinder.
Worn bearings.
Loose flywheel.
Gasoline mixture in tank.

Decoke.
Fit new nozzle.
Check/adjust end of delivery.
Fit new rings.
Overhaul engine.
Overhaul engine.
Tighten flywheel nut.
Change fuel.

Major fluctuations in speed
(RPMs)

Overheating.
Air in fuel.

Governor sticking or faulty.

Fuel filter choked.
Regulating lever sticking or faulty.

See above.
Check the fuel system for leaks /
check the return line.
Check / repair / renew governor.

Renew filter.
Check / renew.

Engine stops suddenly.

Empty fuel tank.
Vent valve in tank cap is blocked.
Vapor lock (fuel too hot).
Choked injection nozzle.

Fill with fuel.
Renew tank cap.
Cool fuel.
Check / repair / renew nozzle.

Содержание 15W Series

















































































Отзывы:

Нет отзывов