background image

 

 

 

General Maintenance Cont. 

General Maintenance Cont.

recommended should ever be used 

on vinyl coated fabrics. Misuse of 

solvents can permanently damage 

the fabric's finish. Brand-name 

cleaners are effective only if used 

strictly in accordance with their 

instructions. 

Trailer 

A. Trailer maintenance:- 

Your Farr 

6000 trailer is either of modern 

a l u m i n i u m   c o n s t r u c t i o n   o r  

galvanised steel. In either case the 

following check list should be 

followed to maintain your trailer in 

top condition. 
2.

 

It is essential that the wheel 

bearings are kept well greased at 

all times. 

3.

 

Hose your trailer down with fresh 

water after salt water use. 

4.

 

Before towing check tyre 

pressures and tread, lights and 

warrant of fitness, and 

registration. 

5.

 

Periodically check that the side 

supporting pads are correctly 

adjusted. 

NOTE 

The total weight of 

the boat must be supported by the 

centre rollers of the trailer 

under the keel and not the side 

support pads which are for 

stabilising the boat only and 

should be set approximately 1/4" 

from the hull to allow for easy 

launching. 

1.

 

Periodically check that your 

wheel studs are tight. Remember 

— It is human nature to overlook a 

trailer which is out of sight 

beneath your boat. Your boat and 

trailer weigh almost one ton 

when towed behind your 

vehicle. For your own and 

everyone elses safety a 

roadworthy trailer is essential. 

B. Trailer use 

1.

 

When towing your Farr 6000 long 

distances remember to ease the 

keel winch off so that the weight 

of the keel rests on the trailer and 

is not suspended by the wire 

only. 

2.

 

Check that the trailer safety 

chain is connected and that the 

rudder, outboard motor, fuel 

tank and pop top are securely 

fastened. 

3.

 

Always use a safety line from 

the boat to the trailer when 

trailering t h e  b o a t  o r  

l a u n c h i n g   o r   retrieving. 

How to back up a trailer:- 

We will 

attempt to show you how it is done in 

pictures. However, practice makes 

perfect, so we suggest an empty 

supermarket parking lot can be the 

biggest benefit. 

Note: When backing, be sure to 

have a lookout — your visibility may 

be severely impaired. 
1.

 

Turn the front wheels of the car 

the opposite direction from which 

you want to go. 

2.

 

Once turn is started, follow the 

trailer as you would normally 

backing the car. 

3.

 

When rounding turns on 

highways or streets, do not cut 

corners. 

4.

 

Equip your vehicle with a left 

hand mirror — a real benefit when 

passing and parking. 

 

Backing to 

right 

Backing to left 

 

Following thru turn 

Содержание 6000

















Отзывы: