FarmTek Growers Supply GrowSpan Gothic Premium 106205 Скачать руководство пользователя страница 31

Страница: 31 / 49

GROWSPAN

™

GOTHIC PREMIUM GREENHOUSES

Revision date: 06.28.18

106205_06_07_08

INSTALL OVERLAP BRACING AND U-CHANNEL — continued

NOTE:

Do not climb on panels to install screws. Take

steps to protect panels during screw installation.

6. Repeat steps as needed to cut and attach additional

1.5" x 1.5" square tubes to secure overlap seam of all

panels.

Install one tube per overlap as shown.

7. Install an additional Tek screw and washer at end of

H-channel if needed to secure channel to rafter. See

photo in Step 5.

8. Continue by reading baseboard installation information

on next page.

ATTENTION:

If you are not installing a baseboard,

skip to and continue by sealing greenhouse using the

supplied silicone sealant.

View from outside of the shelter.

Upper Panel

Installed 104213

U-Channel

Lower Panel

Step 7

5. With tube aligned and someone holding it in place

inside the greenhouse, drive FA4484B Tek screws with

neo-bonded washers through from the outside into the

1.5" x 1.5" backer tube (104779).

Inside

Greenhouse

Drive FA4484B Tek screw with

102921 neo-bonded washer

through U-channel, both panels,

and into 1.5" x 1.5" square tube.

Space screws at 12" on-center.

Lower

Panel

Outside

Greenhouse

Upper

Panel

104213

U-Channel

104779

Backer Tube

Содержание Growers Supply GrowSpan Gothic Premium 106205


















































Результаты поиска

Содержание Growers Supply GrowSpan Gothic Premium 106205

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Gothic Premium 106205

Бренды по названию

Популярные бренды

FarmTek Growers Supply GrowSpan Gothic Premium 106205, Инструкция по эксплуатации

Результаты поиска

Содержание Growers Supply GrowSpan Gothic Premium 106205

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Gothic Premium 106205

Бренды по названию

Популярные бренды