FarmTek Growers Supply GrowSpan 106310D Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 53

background image

19

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

Revision date: 05.29.19

INSTALL END WALL FRAMING (BACK)
The greenhouse end walls (front and back) are identical

except as noted below and on the end frame diagrams.

If the back wall includes the optional double door kit

(additional purchase required), repeat the End Wall

Installation procedure and install the framing for the

remaining end wall.

If the back wall

does not

include an optional double door

kit,

consult the end frame diagram

to install the vertical

frame members.

Dashed lines show where additional frame tubes are

installed when the optional double door is not used.

Consult the end frame diagram for additional information.
1. Read the note regarding the installation of optional

accessories at the beginning of the end wall installation

section.

2. Cut the tubes to the required length and attach to the

end wall framing.

3. Attach the frame supports at the top and bottom as

previous described.

TAPE SHARP EDGES AND CONNECTORS

After the frame is assembled, check the frame for sharp

edges that could damage the cover or end panel, and file

these smooth or tape over them using the supplied duct

tape.

In addition, return to the rafters and apply tape over

each connector to better protect the cover film when it is

installed. The following photo shows one way to apply the

tape.

Rafter and frame shown above may differ from actual

frame. Photo is used to illustrate how to apply tape.

Duct tape

over connector

Ground Level

«
...
17
18
19
20
21
...
»

Содержание Growers Supply GrowSpan 106310D






















































Отзывы:

Нет отзывов

Похожие инструкции для Growers Supply GrowSpan 106310D

Бренд: GrowSpan Страницы: 31

30' Wide Pony Wall Building

Бренд: ClearSpan Страницы: 33

Gothic Style Solar Star 104844

Бренд: ClearSpan Страницы: 43

Gothic Style Solar Star

Бренд: ClearSpan Страницы: 45

Бренд: ClearSpan Страницы: 13

Бренд: MyFood Страницы: 52

Бренд: Velcom Страницы: 16

Бренд: ACME Страницы: 8

COMMERCIAL TITAN Peak 240 17.64m2

Бренд: Dancover Страницы: 16

Бренд: Dancover Страницы: 21

Бренд: Dancover Страницы: 28

Homebox Modular

Бренд: EastSide Impex Страницы: 14

Бренд: Dancover Страницы: 32

6x9 Greenhouse Kit

Бренд: Mueller Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды