FarmTek Aquaponics System I Series Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 43

FarmTek Aquaponics System I Series Скачать руководство пользователя страница 36

36

36

Revision date: 12.23.15

Install the Siphon Tubes

17

Siphon tubes slide over the standpipe in each fish-holding tank. As the system operates, water fills each tank and flows out the standpipes to the clarifier tanks

in large systems or biofiltration tanks in smaller systems. Siphon tubes keep fish from swimming into the standpipes while allowing water to pass through side

slots or side holes near the bottom of each tube. This system is equipped with two (2) types of siphon tubes; each serves a specific purpose as your fish grow.

Use the 112742 slotted siphon tube when fish are small. As fish grow and more waste is produced, replace the 112742 slotted tube or tubes with the 112743

tube with 1-1/8" holes. These holes help ensure a consistent water flow as the fish grow.

Install Siphon Tubes

Photo shows the standpipe as installed

inside the fish-holding tank. Air lines to

aerator stones are also shown.

1. Slide siphon tube down into tank and

over the standpipe.

Siphon tube with 1-1/8" holes is used for

larger fish.

Photo (left) shows a slotted

siphon tube for smaller fish.

2. Carefully seat siphon tube inside tank.

Length of tube must be above the water

level in the tank. Tube can be trimmed

to 1"-2" or so above tank if desired.

«
...
34
35
36
37
38
...
»

Содержание Aquaponics System I Series












































Отзывы:

Нет отзывов