FarmTek Aquaponics System I Series Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 43

FarmTek Aquaponics System I Series Скачать руководство пользователя страница 14

14

14

Revision date: 12.23.15

Prepare and Install Aluminum Retaining Strap

7

Take the 112480 aluminum flat stock and mark the mounting hole locations according to the diagram below. Use a 1/4" drill bit to drill the fastener

holes in the center of the stock at 8" on-center. Do not drill these around or on the float bed frame or liner. Doing so can cause filings to drop into the

water. These will damage the water pump once it is installed and running. Drill in a drill press if possible to keep holes uniform. Cut drilled stock to

length as needed during installation. Attach aluminum retaining strap to frame using the FA4472B Tek screws.

Remove Tek screws and

washers before installing the

aluminum retaining straps.

1. Begin at a corner and remove the Tek screw

and washer to install first prepared strap.

4. Apply slight downward force to stretch liner

material and secure strap with Tek screws.

2. Align strap with end of frame and attach using

the FA4472B Tek screw.

5. Continue attaching straps to the frame until

the entire perimeter of the bed liner is secure.

3. Grip edge of bed liner with duck-bill locking

pliers or similar tool.

6. Using a utility knife or scissors, remove excess

bed liner material. Allow 2"-3" to remain below

the edge of the retaining strap.

Drill end holes after placing strip on

frame. Hole placement will vary.

Drill end holes after placing strip on

frame. Hole placement will vary.

8"

8"

on-center

144"

«
...
12
13
14
15
16
...
»

Содержание Aquaponics System I Series












































Отзывы:

Нет отзывов