FarmTek 112663 Скачать руководство пользователя страница 33

Страница: 33 / 43

Revision date: 12.23.15

PRIMARY BIOFILTRATION TANK FILTER

The primary filter for the biofiltration tank is cut from the

112746

material

provided with your aquaponic system. This material is typically cut to size

and stretched over the open top of the tank under the main return tubes.

This filter collects solids that can circulate throughout the system; it is

cleaned daily. The photo below shows a primary filter installed on the

biofiltration tank. Remove the surface solids using a customer-supplied

plastic scraper or similar tool that will not damage the filter material.

BIOFILTRATION

Air and water turnover are crucial to the health of your system. Follow

these suggestions once your system is up and running:
1. Watch your fish eat and swim. This is really the best way to see how

your system is working. Fish should not swim on their sides or gasp for

air at the top of the tank.

2. Learn to recognize what is “normal” and continually watch for anything

that just does not look right.

3. Check your water chemistry for temperature, pH, ammonia, nitrite,

and nitrate, and especially dissolved oxygen (DO). It will take about 40

days for your water chemistry to “equalize”.

4. Patience is key in aquaponics. Once the biofilter is working properly,

check some of the parameters weekly but until then, it is recommended

to test all parameters daily.

JUMP START YOUR BIOFILTRATION TANK:

One way to “jump start”

your biofilter is to obtain some “seasoned” water from a trusted source*

such as another aquaponic grower.

A five gallon bucket or so will help start bacterial growth in your biofilter

tank. Dump the seasoned water directly into the tank. Once the system is

inoculated with good bacteria, add food. These bacteria eat ammonia; you

can simply add some over the counter ammonia to the water once your

tanks and float bed are filled and the pump is circulating the water. Do this

in small increments. One cup per 500 gallons of water is a good balance.

ATTENTION: DO NOT DUMP THE AMMONIA DIRECTLY INTO THE

BIOFILTER TANK!

Add the ammonia to the float bed, or evenly distribute it

in the fish-holding tanks. Do not use ammonia that may have fragrances or

other additives. Straight ammonia added to the water is required.

*Be sure that the water source is not carrying unwanted diseases that are

detrimental to your system.

Biofilter Start-Up and the Primary Filter

Biofilter Start-Up Information

5. Never modify multiple parameters when troubleshooting the system.

Choose one, make an adjustment, allow the system to equalize, and

check the results.

6. Look for dead fish. If fish are dead, check water chemistry and follow

the previous suggestions to make the necessary adjustments.

7. Keep good records of all changes and results of those changes.

Cut the filter material larger than the top of the tank to allow it to drape over

the sides. Secure material in place using customer-supplied fasteners or

rubber straps. Fastening system should allow for removing the filter for

rinsing and cleaning.

Содержание 112663












































Результаты поиска

Содержание 112663

Отзывы:

FarmTek 112663, Руководство пользователя, Страница: 33 / 43

Результаты поиска

Содержание 112663

Отзывы: