FARMSCAN Jackal Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 52

FARMSCAN Jackal Скачать руководство пользователя страница 23

AM-JACKAL-35 / JULY 2020

21

AREA & SPEED METER SETUP (WIZARD)

The Jackal can display Speed & Area in any combination of km/Ha or mph/acre.

A pickup can be mounted either on a wheel hub or shaft. (Example image right)

NB: THERE SHOULD BE A 5-10MM CLEARANCE BETWEEN SENSOR AND
MAGNET WHEN 2 WIRE SENSORS ARE USED.

NEW STYLE, PROXIMITY SENSORS REQUIRE 4MM SENSING DISTANCE.
THE PICKUP CAN BE MAGNETIC OR RAISED BOLT HEAD.

Sensors Required:

•

Wheel sensor pickup 2 (Reed) or 3 wire (Proximity)

•

Magnet (Used with 2 & 3wire sensor)

Available Connections:

Refer to Installing Sensors from

PAGES 9-11

.

NB: The Implement harness has 3 wires by default. If using our standard wheel
sensor kit, please only use the black & colored wire. The RED (Positive) does not
need to be connected. – Trim this back or cover with heat shrink to prevent
shorting out.

SETUP

From the front screen press

SETUP

Highlight

WIZARD

and press

SELECT

Highlight

Area/Speed Wheel

and

Press

NEXT

Choose your

calibration method

Highlight the

INPUT

number the speed

is connected into the back of Jackal &

press

NEXT

Leave the unit of pulse calibration

method as

M

Auto Set > PAGE 22

Manual Ratio > PAGE 23

«
...
21
22
23
24
25
...
»

Содержание Jackal





















































Отзывы:

Нет отзывов