FARMSCAN Jackal Скачать руководство пользователя страница 20

Страница: 20 / 52

AM-JACKAL-35/ JULY 2020

SETUP – MANUAL MODE (WIZARD) – NOT SO COMMON

The Jackal can be setup to work in

MANUAL

mode in the event of no wheel speed or flow meter input, or

combination of both. Manual mode simply allows adjustment of the flow control valve. In the event of a dump valve
being installed, manual mode will close the dump valve & open all sections when the Run/Hold button is pressed.

Select

MANUAL

: To Adjust

the Flow Control Valve

Manually

Press

SKIP

Press

SKIP

Press

EDIT

and change the

number of sections required

to control.

Press

NEXT

Using the

NAV

EDIT

keys,

highlight and edit the

section width values as

required. The Section

Widths will also Total and be

displayed. Press

NEXT

Press

SKIP

Press

to finalise the

Wizard and return to the front

screen

When you return to the

Front Screen

the Jackal

needs to display a value.

The value of 1.0km/h is not

relevant. It’s simply used for

the manual fucntion

Press the Run/Hold button

You can now manually

adjust your flow control

valve by pressing the Rate +

or Rate –

Simply drive to a set speed

Press the

PAGE

button to display Rate+/-

Flush

Содержание Jackal





















































Результаты поиска

Содержание Jackal

Отзывы:

FARMSCAN Jackal, Руководство пользователя, Страница: 20 / 52

Результаты поиска

Содержание Jackal

Отзывы: