Farmi 381 HF Скачать руководство пользователя страница 6

Страница: 6 / 72

FARMI 381 HFC / HF

GENERAL SAFETY INSTRUCTIONS

These safety instructions are meant for the owners

of FARMI equipment, as well as those who operate, ser-

vice or repair it.

The instructions help with:

• using the machine safely, appropriately and effec-

tively.

• identifying, avoiding and preventing potentially

dangerous situations.

The manufacturer supplies an instruction manual,

which must always be available at the place of ope-

ration of the machine. Each user must read the sa-

fety, maintenance and operating instructions

before operating the machine, and comply with

these instructions at all times.

Ensure that every operator of

the machine is familiar with the

content of the instruction ma-

nual and situation-specific safe-

ty instructions, and has been sui-

tably trained before operating

the machine.

The machine complies with technical requirements

and applicable safety regulations. However, incorrect

use, maintenance or repair of the machine may cau-

se risks.

In addition to the instruction manual, remember to

comply with regulations of the local occupational

health and safety authorities, and with your country’s

laws and decrees.

The manufacturer is not liable for damages caused

by:

• incorrect, negligent or inappropriate use of the

product.

• non-original spare parts.

• normal wear and tear.

• misuse caused by an untrained person’s

improper actions.

• alterations made without the manufacturer’s

permission.

Written authorization must be

requested from the manufacturer

for any alterations to the machine.

STARTING

• Familiarize yourself thoroughly with the use, ope-

ration and controls of the machine and its equip-

ment before starting.

• Familiarize yourself with the capacities and limita-

tions of the machine and its equipment.

• Do not use the machine unless you are complete-

ly familiar with its operation.

• Be aware of the machine’s danger zones.

• During operation, prevent bystanders from ente-

ring the danger zone.

• Ensure that each operator has the necessary safety

equipment, such as a helmet, safety goggles, work

safety boots and suitable protective clothing.

• Never wear loose clothing around moving parts.

Protect long hair!

• Ensure that work is carried out according to the

stipulations of applicable occupational health and

safety legislation.

• Before starting up or using the machine, ensure

that it cannot cause a risk to other people or pro-

perty.

• Perform a safety check on the machine before eve-

ry use. If you observe any faults or deficiencies, re-

pair the machine immediately.

• Before operating the machine, ensure that there

are no foreign articles in it.

• Place the machine on a hard, level surface for

operation. In the winter avoid working in slippe-

ry areas.

• Before mounting and using the machine, check

the PTO drive shaft for correct condition and

attachment.

• Never use a faulty or deficient machine.

CAUTION!

Содержание 381 HF









































































Результаты поиска

Содержание 381 HF

Отзывы:

Farmi 381 HF, Руководство по эксплуатации, техническому обслуживанию и запасным частям, Страница: 6 / 72

Результаты поиска

Содержание 381 HF

Отзывы: