Farmi Forest Corporation CH380HF Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 64

background image

CH380HF

28

KNIFE MAINTENANCE

Please refer to the safety instructions. The

chipping disc continues to rotate freely in

the manner of a flywheel after the power

take-off has been disconnected.

Use protective gloves when handling the

knives.

OPENING AND REMOVAL OF THE UPPER

CHAMBER

o  Remove the M16 (3 pcs) locking screws.
o  Turn the upper chamber onto its side.
o  Lock the disc with the locking bolt.
o  Remove the feed chute or turn it to the side.

KNIFE REMOVAL FROM

THE KNIFE HOLDERS

1. Remove the knife’s lock nuts (M14).
2. Remove the knife fastening bolts (M14). Turn
  the wrench carefully to avoid hand injury by
  the knife should the wrench slip.

Locking the disc and removing the lock nuts

Locking

bolt

MAINTENANCE

Opening the upper chamber

Removing the knife fastening bolts

«
...
26
27
28
29
30
...
»

Содержание CH380HF

































































Отзывы:

Нет отзывов

Похожие инструкции для CH380HF

Бренд: KaVo Страницы: 13

Бренд: vc999 Страницы: 52

Бренд: ACE INSTRUMENTS Страницы: 15

Бренд: Wave Fitness Страницы: 15

Бренд: Tascam Страницы: 8

Бренд: B-K lighting Страницы: 5

Бренд: B-K lighting Страницы: 4

Бренд: B-K lighting Страницы: 3

Бренд: Bartscher Страницы: 28

Бренд: Bartscher Страницы: 13

Бренд: IBEX Страницы: 10

Бренд: M-system Страницы: 12

Бренд: Federal Signal Corporation Страницы: 2

Бренд: Harman Kardon Страницы: 7

Бренд: Jasco Страницы: 2

Бренд: Jacto Страницы: 12

Бренд: Octane Fitness Страницы: 20

Бренд: Oceaneering Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды