Fargo HDP600-LC CR100 Скачать руководство пользователя страница 155

Страница: 155 / 432

RESTRICTED USE ONLY

Fargo Electronics, Inc.

HDP600 High Definition Card Printer/Encoder User Guide (Rev. 2.5)

4-55

Resolving a Ribbon Sensor Error (Ribbon Miscue)

Step Procedure

Open the front cover and remove the Ribbon.

a. Check that the Ribbon is in good condition and not wrinkled or broken.

b. If Ribbon is broke or wrinkled, repair the Ribbon and wind up the take-

up roll 4-color panels past the damaged area.

Press on the

Resume

button.

If the issue persists, continue to Step 4.

Replace the Ribbon.

a. Press on the

Resume

button.

b. If the issue persists, continue to Step 5.

5 Press

the

Cancel Print

button on the Driver Monitor Error Display

Message.

Reboot the Printer by cycling the power.

Using the driver calibration tab calibrate the Ribbon Sensor.

If the issue persists, continue to Step 8.

Replace the Ribbon Sensor.

Содержание HDP600-LC CR100

















































































































































































































































































































































































































































Результаты поиска

Содержание HDP600-LC CR100

Отзывы:

Похожие инструкции для HDP600-LC CR100

Бренды по названию

Популярные бренды

Fargo HDP600-LC CR100, Руководство пользователя

Результаты поиска

Содержание HDP600-LC CR100

Отзывы:

Похожие инструкции для HDP600-LC CR100

Бренды по названию

Популярные бренды