Directive 2014/30/EU (Electromagnetic Compatibility (EMC))
Directive 2012/19/EU (WEEE)
Directive 2011/65/EU (RoHS)
Harmonised standards: EN 61000-6-1 Immunity for residential, commercial and light-industrial environments
& EN 61000-6-3 Emission standard for residential, commercial and light-industrial environments
INSTALLATION
To install the Faradite Motion
Sensor 360, cut a 35mm hole using
a suitable hole saw. Fold the spring
clips upwards and push through the
hole. If you are using the optional
Fire IDR to achieve a 60 minute fire
rating to BS 476: Part 21 1987, then a
40mm hole will be required.
USE A 35mm
HOLE SAW FOR
INSTALLATION
For further support please visit: faradite.com
CONNECTION TO LOXONE MINISERVER
Connection to Loxone is simple: connect the motion output to a digital
input and the lux sensor output to an analogue input. There is no need
to invert the input as the motion sensor is logic high for motion - see
motion output diagram.
Simply connect directly using a CAT cable; no pull-up resistors required
CONNECTION TO LOXONE NANO DI TREE
LOXONE CONFIG ADJUSTMENT OF ANALOG INPUT
The analog input needs to be mapped correctly so 10V is interpreted as
1000 Lux.
To do this:
click on the correct analog input, which will bring
up the properties on the left hand side of the Loxone config. Find the
correction section and change the “Display Value 2” to 1000 (instead of 10).
If you are installing Faradite TAP-5 / TAP-1 switches as well, the
recommended option is to connect the Motion Sensor 360 to the 6th
Digital input of the Nano DI Tree module.
Please note that Loxone Nano
DI Tree module does not have an analog input for the Lux sensor
0V / GND
LUX 0V - 10V
12V-24V
MOTION
GND
ANALOGUE INPUT
24V
DIGITAL INPUT
FARADITE MOTION
SENSOR 360
LOXONE
0V /GND
12V-24V DC
MOTION
GND (WHITE WAGO)
6th INPUT (BLACK WIRE)
24V (ORANGE WAGO)
FARADITE MOTION
SENSOR 360
NANO DI TREE
MOUNTING & SAFETY
PRECAUTIONS
1) Do not under any circumstance
use these sensors outside the range
of their ratings shown in the technical
data.
2) Faradite is committed to making
products of the highest quality and
reliability. Nevertheless, all electrical
components are subject to natural
deterioration, and the product
durability will depend on the
operating environment and
conditions of use.
3) Please note that the sensor can
detect heat sources other than the
human body, such as:
a) Small animals
b) Direct sun light, incandescent
lamps, car headlights (even if the heat
source is outside the detection area)
c) Sudden temperature change inside
or around the detection area i.e. hot
or cold winds/drafts or vapour from
the humidifier can effect the
performance of the sensor.
4) Please note that the sensor will
have difficulty sensing the heat
source if it is behind glass, acrylic or
similar materials as these materials
may not allow a correct transmission
of infrared rays.
CONNECTION TO CONTROL4
Connection to Control4 is simple, the motion sensor output can be
connected to a contact closure on a Control4 I/O module. The 0-10V LUX
sensor can be used with Control4 using a driver from Janus Technology.
The driver allows for connection of the 0-10V and digital input via devices
from Brainboxes Ltd. Search online for Faradite Janus Technology for
more info.
0V /GND
12V-24V DC
LUX 0V-10V
GND
12V
FARADITE MOTION
SENSOR 360
CONTROL4
MOTION
Brainboxes ED588 - Digital Input
OR Control4 - Contact Closure
SENSITIVITY ADJUSTMENT
The sensor has been designed for optimal sensitivity.
It is not recommended to change the sensitivity
setting unless it is found to be necessary. To adjust
the sensitivity, remove the two screws and turn over
the circuit board. The small potentiometer can be
used to adjust the sensitivity.
0-10V - Brainboxes ED549
