background image

Caution: 

Be sure to turn the ON/OFF switch to the "OFF" position and disconnect 

the

                power cord from the wall outlet before cleaning the filters.

CLEANING THE SUB-FIL TER

   Clean the sub-filter when it becomes dirty.

            Remove the dust compartment
            (refer to page 8).
            Remove the air inlet cover.

         Remove the sub-filter from the vacuum

        cleaner.

         Gently clean the sub-filter with water.

        
       Make sure that it is completely dry and 
       then re-install it into the vacuum cleaner. 
       Replace the air inlet cover and the dust 
       compartment.

 

  Caution

: Do not wash the air outlet filter and sub-filter in a washing machine, and do not 

                    use any other equipment such as a hair dryer to dry it.  Do not operate the vacuum 
                    without the sub-filter. Be sure the filter is dry and properly installed. Failure to do 
                    so could result in electrical shock, personal injury, or motor failure.

CLEANING AND REPLACING THE 
SECONDARY FILTERS

Remove the filter cover.

1

1

2

3

4

HEPA Filter

10

2

Remove the HEPA  filter from the 
filter cover.

Filter Cover

1

1

1

1

2

2

Sub-Filter

2

2

1

1

Air inlet 
Cover

         Replace the HEPA  filter.

3

Caution:  

The HEPA  filter cannot be 

                 reused.

         Replace the filter cover.

4

  Depending on usage and conditions, the HEPA filter lasts 3 to 6 months; 
  however, vacuuming large amounts of extremely fine dust, powder or similar 
  material over a long period of time may decrease airflow performance through 
  the filter. If  this occurs,  it may  become necessary  to replace  the HEPA
  Filter.  Only use  genuine FANTOM  replacement filters.

Содержание FM740



















Отзывы: