8.
Flash Up Switch
- Rotating this control
up the camera built-in flash. Note that once th
disabled again using the
Flash / Right
Rotating the
Flash Up Switch
counter
9.
Control Ring
– Rotating this knob activates the function that you have assigned to the Control Ring.
Please refer to the camera instruction manual to assign a function to the Control Ring.
Important Notice! The preferred Control Ring function should be assigned
inserting the camera into the housing
not be accessible through the housing
10.
Lens Port-
The housing lens port
“wet” accessory filters and lenses
filters. In order to maintain the threads of the lens port, it is recommended to apply a small amount
of silicone grease to the threads on the housing
For a selection of lens accessories available, visit the Fantasea website
11.
Tripod Mounting Screw Holes –
addition of various image enhancement accessories
any one of 3 adjustment positions, you can better determine how and where to position the housing
on the tray. This configuration also allows for the use of 2 set screws for the tray mount, thereby
preventing any swiveling of the housing on the
12.
Lanyard Loops –
The 4 lanyard
Hand Strap to the housing, as well as to secure accessories using snap cords or secure strings.
Important Notice
Screws longer than 7mm should not be screwed into the
Mounting Plate, as they might damage the plate and housing.
FG7X III R Housing Instruction Manual
9
ing this control clockwise (pulling it towards the back of the housing)
Note that once the camera built-in flash has been popped up, it can be
/ Right
control and selecting “flash disabled” on the flash mode menu
counterclockwise will not have any effect on the built
Rotating this knob activates the function that you have assigned to the Control Ring.
Please refer to the camera instruction manual to assign a function to the Control Ring.
The preferred Control Ring function should be assigned on the camera
amera into the housing, as in various shooting modes, Control Ring assignment
accessible through the housing.
The housing lens port features a 67mm thread and it’s compatible with a wide vari
accessory filters and lenses, including macro lenses, wide angle lenses and color correction
filters. In order to maintain the threads of the lens port, it is recommended to apply a small amount
of silicone grease to the threads on the housing port and on the accessory lens prior to installation.
For a selection of lens accessories available, visit the Fantasea website
www.fantasea.com
–
Enable mounting the housing on a tray, thereby
of various image enhancement accessories to your underwater photo system
any one of 3 adjustment positions, you can better determine how and where to position the housing
This configuration also allows for the use of 2 set screws for the tray mount, thereby
preventing any swiveling of the housing on the tray.
loops featured on the housing are used to attach a Hand Lanyard or
Hand Strap to the housing, as well as to secure accessories using snap cords or secure strings.
Screws longer than 7mm should not be screwed into the
Mounting Plate, as they might damage the plate and housing.
Instruction Manual 20200220
clockwise (pulling it towards the back of the housing) will pop-
in flash has been popped up, it can be
control and selecting “flash disabled” on the flash mode menu.
clockwise will not have any effect on the built-in flash.
Rotating this knob activates the function that you have assigned to the Control Ring.
Please refer to the camera instruction manual to assign a function to the Control Ring.
on the camera prior to
Control Ring assignment might
compatible with a wide variety of
, including macro lenses, wide angle lenses and color correction
filters. In order to maintain the threads of the lens port, it is recommended to apply a small amount
port and on the accessory lens prior to installation.
www.fantasea.com
Enable mounting the housing on a tray, thereby allowing for the
underwater photo system. By choosing
any one of 3 adjustment positions, you can better determine how and where to position the housing
This configuration also allows for the use of 2 set screws for the tray mount, thereby
are used to attach a Hand Lanyard or
Hand Strap to the housing, as well as to secure accessories using snap cords or secure strings.
Screws longer than 7mm should not be screwed into the housing Tripod
Mounting Plate, as they might damage the plate and housing.
