manualshive.com logo in svg

F&U PAH-1029, Инструкция по эксплуатации, Страница: 14 / 15

Поделиться
Скачать
F&U PAH-1029 Скачать руководство пользователя страница 14

flat surface.   

place (to reduce noise). 

The  compressor 
does not work.   

Overheat protection starts.   

Wait  for  3  minutes  until  the  temperature  is 
lowered, and then restart the machine. 

The remote 
control does not 
work. 

The distance between the machine and 
the remote control is too far. 

Let  the  remote  control  get  close  to  the  air 
conditioning, and  make sure  that  the remote 
control  directly  faces  to  the  direction  of  the 
remote control receiver. 

The remote control is not aligned with 
the  direction  of  the  remote  control 
receiver. 

Batteries are dead.   

Replace batteries.   

Displays 'E1'. 

The  pipe  temperature  sensor  is 
abnormal.   

Check the pipe temperature sensor and related 
circuitry. 

Displays 'E2' 

The  room  temperature  sensor  is 
abnormal.   

Check  the  room  temperature  sensor  and 
related circuitry. 

 

Note: If problems not listed in the table occur or recommended solutions do not work, please 
contact the professional service organization. 

VIII.

 

Appendix 

Schematic Diagram for Cooling & Heating model 

 

 

For all the technical and specific parameters, please refer to product nameplate. 
 
 

 

Condenser 

Compressor 

Evaporator 

Capillary 

Содержание PAH-1029
















Отзывы:

Нет отзывов