background image

• 

DO NOT extend the lifeline past the operational limit.

• 

DO NOT allow one SRD lifeline to become tangled or twisted with another SRD lifeline during use.

• 

DO NOT allow any lifeline to pass under arms or between legs during use.

• 

DO NOT clamp, knot, or prevent the lifeline from retracting or being taut.

• 

DO NOT lengthen the SRD by connecting a lifeline or similar component.

• 

DO NOT allow the lifeline to remain outside the housing when not in use. 

102022

MSRD26 Rev B

9

5.4.3 

After A Fall:

 A fall event over an edge may require special rescue equipment and measures. Ensure a written rescue plan, method and  

 

 

system is in place and readily available to all users for rapid response. Ensure all users are trained in rescue procedures. If a fall event  

 

 

occurs, remove it from service, and store it separately. Remove from service any unit that has been subjected to fall arrest forces or that 

 

exhibits damage consistent with such forces. For questions, contact FallTech.

5.4.4 

Using the SRD:

 Do not use the SRD if inspection shows damage or any malfunction. Don the FBH in accordance with the FBH 

 

manufacturer’s instructions. Follow the instructions contained in this manual and on the labels. Failure to follow instructions may result 

 

in serious injury or death. Connect the SRL-FBH Connector to the dorsal D-ring on the FBH. Ensure the connector closes and locks. Attach    

 

the leg-end carabiner to the chosen anchorage and ensure the leg-end connector closes and locks. Ensure all connections are compatible.   

 

Normal operation will allow the working length of the lifeline to extend and retract as the worker moves about. A certain amount of 

 

tension must remain on the web at all times to ensure proper operation of the internal brake. Do not allow the lifeline to become slack. 

 

If the lifeline becomes slack, remove the SRD from service for inspection. See Section 7.

 

Avoid sudden or quick movements during the normal work operation, as this may cause the SRD brake to engage and possibly cause loss    

 

of balance and injury or death.

 

If a fall occurs, the brake will engage and lock the lifeline. The EA will deploy to arrest the fall and limit arrest forces on the user.

Содержание 11' FT-X Web Class 1 SRL-P


















Отзывы: