Falcon Professional + FX Скачать руководство пользователя страница 31

Страница: 31 / 48

INSTALLATION

Check the appliance is electrically safe and gas sound when you have finished.

ArtNo.011-0007 - Restraining chain (AUS)

Restraining

chain

Fitting the stability bracket and
chain

A stability bracket and chain MUST be fitted when

the cooker is connected to a flexible gas supply.

Unless properly installed, the cooker could be tipped by

leaning on the door. Injury might result from spilled hot

liquids or from the cooker itself.

IMPORTANT: The cooker must be set to the correct

height and levelled before the stability bracket is

installed.

Fitting a stability bracket

When fitting a stability bracket please refer to the instructions

supplied with the bracket for further details on fitting.
When fitting a stability bracket (

Fig. 9.6

and

Fig. 9.7

) adjust

the bracket to give the smallest practicable clearance

between the bracket and the engagement slot in the rear of

the cooker.
Fit the bracket so that it engages as far as possible over the

chassis of the cooker.

Fitting the restraining chain

The restraining chain

MUST

be fitted.

The length of chain between the appliance and the wall fixing

should prevent strain on the gas and electricity connections,

but still allow access to unhook the chain when the cooker is

pull forward.
Measure the length of chain required. Use the hexagon-

headed screw, washers and bolt supplied in the restraining

chain kit to fix the chain to one of the holes at the top of the

flue trim bracket (

Fig. 9.8

Hook the other end of the chain to the wall fixing.

ArtNo.070-0014 - Stability bracket - Wall fitting

Cooker

Stability bracket

Floor

3 mm min

Typical floor mounting

Cooker

Outer stability

bracket

Floor

Wall

3 mm min

Typical wall mounting

Fig. 9.6

Fig. 9.7

Fig. 9.8

Caution, possibility of tilting

Anti-tip restraints

Содержание Professional + FX

















































Результаты поиска

Содержание Professional + FX

Отзывы:

Похожие инструкции для Professional + FX

Бренды по названию

Популярные бренды

Falcon Professional + FX, Руководство пользователя и инструкции по установке

Результаты поиска

Содержание Professional + FX

Отзывы:

Похожие инструкции для Professional + FX

Бренды по названию

Популярные бренды