background image

mbar

inches w.g.

6

14.8

15
37

NATURAL

PROPANE

1.9 GAS PRESSURE

NATURAL and PROPANE GAS

1.10 BURNER ADJUSTMENTS
Noadjustments are provided, since burners have

fixed injectors and aeration.

SECTION 2 - ASSEMBLY and

COMMISSIONING

2.1 ASSEMBLY
1. Check parts supplied Check that each pan is

equipped with twochip baskets, pan base panel

and dust cover. (These parts may be packed

separately). On NATURAL gas models, an

adjustable governor is also supplied.

2. Place unit in position, and level using feet

adjusters. For safety reasons, both units must be

fixed to floor. Holes are provided in feet for this

purpose.

2.2 CONNECTION TO THE GAS SUPPLY
Installation should be carried out in accordance with

various regulations listed on the cover of this manual.
On NATURAL gas appliances, the adjustable

governor supplied must be fitted in supply. Securely

fixed in a position enabling adjustment to be made

during commissioning. On propane appliances, do

not fit a governor.

2.3 CONNECTION TO AN ELECTRICITY SUPPLY
Not applicable to these appliances.

2.3 CONNECTION TO A WATER SUPPLY
Not applicable to these appliances.

2.5 PRE-COMMISSIONING CHECK
After connecting gas supply, fit a pressure gauge to

pressure test point, and check installation for gas

soundness.
To remove protective surface film from pan, clean

pan thoroughly using hot water and detergent.

Rinse out and dry.
Ensure drain valve is closed and fill pan with oil to

level indicated on rear wall of pan.
Purge air from system and light burner using the

following procedure:

Warning
If pilot is extinguished either intentionally or

unintentionally, wait at least 3 minutes before

re-lighting gas.
a) Ensure that pan contains oil up to level mark

embossed on rear wall of the pan.

b) Open cabinet door, gaining access to controls.
c) Refer to Figure 2 and turn thermostat knob

clockwise to pilot position .

d) Press rectangular button marked

and hold in.

e) Press spark igniter button and observe that pilot

lights. If it does not light immediately, repeatedly

press and release ignition button until it does.

f) Hold ignition button in for a further 20 seconds and

release button. Observe that pilot remains lit.

If it should go out, wait three minutes then repeat

from (d).

g) Having established pilot, turn control knob anti-

clockwise to maximum setting and main burner

will light.

h) On NATURAL gas units, if necessary, adjust

governor to produce required pressure of 15mbar

(6 inches w.g.) on gauge previously fitted.

To affect this, remove governor cap to access

screw and turn it clockwise to increase pressure

and vice-versa. Replace governor cap after

correct pressure has been established.
Allow pan to heat up and check that thermostat

shuts off gas to main burner when maximum

temperature is reached.

j) When satisfied that fryer is functioning properly,

shut off gas by pressing OFF button (Figure 1).

k) Remove pressure gauge and replace pressure

test-point screw.

Note
The main burner can be shut off while leaving pilot lit

by turning control knob clockwise to the

position.

Figure 1 - Gas Control Valve

All manuals and user guides at all-guides.com

Содержание G350/12








Отзывы: