WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity before servicing. Check appliance is safe when you have finished.
33
5.
To Change a Hotplate Tap
Disconnect from electricity supply.
Remove the hotplate top (see 3). Unplug the FSD lead from
the rear of the tap and undo the compression fitting. Remove
the fixings that secure the tap to the gas rail. Remove the tap.
Remove and discard the gasket seal.
Fit the new gasket seal to the replacement tap. Reassemble in
reverse order.
Ensure that the valve is adjusted for correct gas operation.
Check that the cooker is gas sound. Check hotplate ignition.
6.
To Replace a Hotplate Burner Jet
Disconnect from electricity supply.
Remove the burner cap and head
(Fig.9-4)
. Remove the old
jet. Fit the new orifice.
Note:
The Wok burner has 2 orifices.
Reassemble in reverse order. Check that the appliance is gas
sound.
7.
To Change a Hotplate Burner Electrode
Disconnect from electricity supply.
Lift off the pan supports and remove the burner cap. Remove
the screw holding the electrode. Pull the electrode vertically
up sufficiently to grip the lead between thumb and forefinger.
Pull off the electrode, but keep hold of the lead. Fit the new
electrode to the lead. Fix the electrode in the burner with
the screw. Replace the burner cap. Check the burner ignition.
Replace the pan supports.
8.
To Remove or Change a Hotplate Burner
Disconnect from electricity supply.
Remove the hotplate top (see 3). Remove the control panel
(see 2).
Centre Hotplate Burners
The burners are mounted in pairs on the cross supports.
Disconnect the burner feed pipes at the burners. Remove the
screw at the front holding the cross support
(Fig.9-5)
. Slide
the support to the right to release it from the rear location.
Lift the cross support and burners clear. The burners are fixed
to the cross supports with screws underneath. Remove the
appropriate burner and fit the new one.
Reassemble in reverse order. Check that the burner operation
is satisfactory.
Wok Burners
Disconnect the burner feed pipes at the burner. Fit the new
one and reassemble in reverse order. Check that the burner
operation is satisfactory.
9.
To Change Ignition Generator
Disconnect from electricity supply.
Pull the cooker forward to gain access to the cover box at
the rear of the left hand oven. Remove the screws securing
the cover and lift clear. Pull off all the leads to the generator,
noting their positions. Slacken the two screws holding the
generator to the cooker and remove the generator.
Fit the new generator to the cooker and replace the leads,
referring to the wiring diagram. Reassemble in reverse order.
Check ignition performance.
10. To Replace the Light Switch
Disconnect from electricity supply.
Remove the control panel (see 1).
Note:
The old switch may be destroyed during removal.
Remove the old switch from its bezel by gripping the switch
body behind the control panel and twisting sharply. Remove
the switch bezel by folding back its locking wings and pushing
forward.
Fit the new bezel to the control panel by first lining up the
raised key on its body with the cut-out in the control panel
and pushing it in from the front.
Assemble the new switch to the bezel by lining up the key
sections and pushing home. Fit the new button by pushing in
from the front.
Replace the Control Panel in reverse order and test for correct
operation.
11. To Remove the Electronic Timer
Disconnect from electricity supply.
Pull off the timer control button(s) and remove the control
panel (see 2).
Remove the timer/mounting bracket assembly from the
control panel by removing the fixing screws.
Remove the timer from its mounting bracket by depressing
the plastic lugs on the timer case, at the same time pulling the
unit forward.
Reassemble in reverse order. When replacing the leads, refer
to the wiring diagram in this manual. Check the operation of
the timer.
12. To Replace a Thermostat
Disconnect from the electricity supply.
Remove control panel (see 2) and hotplate top (see 3). Open
the oven door and remove the oven furniture.
For the right-hand oven, remove the oven roof. Remove the
thermostat phial cover (two screws). Unclip the thermostat
phial from the clips in the oven back.
For the left-hand oven, remove the two screws holding the
thermostat phial to the oven fan cover at the rear of the oven.
Pull the unit forward to access the rear of the cooker. Remove
both rear cover boxes by removing the fixing screws and
lifting clear.
Feed the thermostat capillary clear of the oven. Disconnect
the wires from the thermostat and undo the two fixings that
secure the control to the mounting plate. Fit the replacement
and reassemble in reverse order. Ensure that the phial is
clipped to the oven rear, positioned centrally between the
clips.
Check the operation of the thermostat.
