Falcon Dominator Plus G3800 Скачать руководство пользователя страница 24

24

 

 

Warranty Policy Shortlist 

 

Warranty 

does not

 cover the following:- 

• Correcting faults caused by incorrect installation of a product. 

• Where an engineer cannot gain access to a site or a product. 

• Repeat commission visits. 

• Replacement of any parts where damage has been caused by misuse. 

• Engineer waiting time will be chargeable. 

• Routine maintenance and cleaning. 

• Gas conversions i.e. Natural to Propane gas. 

• Descaling of water products and cleaning of water sensors where softeners/ conditioners 

are not fitted, or are fitted and not maintained. 

• Blocked drains 

• Independent steam generation systems. 

• Gas, water and electrical supply external to appliance. 

• Light bulbs 

• Re-installing vacuum in kettle jackets. 

• Replacement of grill burner ceramics when damage has been clearly caused by misuse. 

• Where an engineer finds no fault with a product that has been reported faulty. 

• Re-setting or adjustment of thermostats when appliance is operating to specification. 

• Cleaning and unblocking of fryer filter systems due to customer misuse. 

• Lubrication and adjustment of door catches. 

• Cleaning and Maintenance  

• 

Cleaning of burner jets 

• 

Poor combustion caused by lack of cleaning 

• 

Lubrication of moving parts 

• 

Lubrication of gas cocks 

• 

Cleaning/adjustment of pilots 

• 

Correction of gas pressure to appliance. 

• 

Renewing of electric cable ends. 

• 

Replacement of fuses 

• 

Corrosion caused by use of chemical cleaners. 

Содержание Dominator Plus G3800

























Отзывы: