background image

M-BFS35-45ow.doc

Issue 3225-Aug 01

7

A more comprehensive manual suitable for workshop use is available from Fairport
Construction Equipment Ltd.

8.

WARRANTY CONDITIONS AND CLAIMS PROCEDURE

All products supplied by Fairport Construction Equipment Ltd (hereafter referred to as
FCE) are warranted to be free of defects due to faulty materials or workmanship for a
period of 12 months from the date of original despatch from FCE or as specified
below:

Hydraulic hoses and hydraulic couplings – 3 months.
Hydraulic accumulators – 6 months.
Flexible drives – 6 months.
All spare parts used in repairs carried out by FCE or an authorized dealer or
repairer – 3 months.

If the goods have been purchased through a stockist the above warranty periods also
apply from receipt of the goods by the user of the equipment up to a total of a further
6 months from date of despatch from FCE whichever is earlier.

Filter elements, gauges and oils are specifically excluded from this warranty.

FCE shall at their option repair or replace during normal working hour’s goods
accepted as faulty free of charge to the user.

For proprietary items such as engines, the original manufacturer’s warranty and
conditions shall apply.

CONDITIONS

The goods shall be returned at the purchaser’s expense to FCE or to a destination
FCE may reasonably direct. Carriage costs will be refunded if warranty is accepted.

Warranty claims will not be considered where there is evidence that failure has been
caused by carelessness, improper use, negligence, inadequate servicing, incorrect
engine speeds, fair wear and tear or non-compliance with instructions issued by the
manufacturer.

To the extent permitted by law, the liability of FCE under this section is confined only
to providing a remedy for defective goods and does not extend to any consequential
loss, loss of profit, injury or damage suffered.

Warranty will not be accepted on dismantled goods unless dismantling was carried
out with the written permission of FCE.

No claim shall be considered if other than genuine parts supplied by FCE have been
used.

Содержание BFS35











Отзывы: