background image

 

 

SMART Temperature Transmitter 

 

PTT74-Ex Series User Manual

        

Sep.2020    

 

18 

www.faraboard .com 

FAHM Co

Industrial Automation 
Doc. PTT74-ExRev99/07M 

 

According to Hart protocol, user can select a number between 0 and 15 as poll identifier. If 
user select zero, the device multi-drop mode will be disabled and the current output will 
show the primary variable value. But if user select a number greater than zero, the device 
will go into multi-drop mode and the output current will be fixed at 4.0 mA. 

3.2.6

 

Reset Factory 

User can recall all factory settings using bellow menu.  

The default password for this operation is “74” 

parameter 

display

 

Parameter tuning structure

 

Reset Factory 

(Password factory 

setting)

 

 

Press <M> until this page is appeared on LCD. Then press 
<Z>  to  access  the  reset  factory  setting  (programing 
mode). You can  enter the password  by <S>  and change 
the  point  and  position  of  digits  by  <Z>.  After  entering 
the  correct  password,  press  the  <Z>  until  all  characters 
blink. Then press <M> for recall the factory settings and 
restart the device. 

 

3.2.7

 

Sensor Configuration 

PTT74-Ex  series  transmitters  has  universal  input  terminals  to  measure  the  value  which 
produced by sensor element. So user should configure the transmitter to identify the type 
of sensor element and related parameters. There are some menu in this device to configure 
the sensor element: 

3.2.7.1

 

Sensor Type 

Universal input port of device allow user to connect any temperature sensor element type 
to device. User can configure the sensor type using bellow menu: 

parameter 

display 

Parameter tuning structure 

Sensor Type 

(The sensor element 

type)

 

 

Press <M> until this page is appeared on LCD. Then press 
<Z> to access  the  Sensor Type  (programing mode). You 
can  select  the  sensor  type  by  pressing  <S>.  After  that, 
press  <Z>  until  all  characters  blink.  Then  press  <M>  for 
the  saving  new  parameter  and  switching  from 
programing mode to operation mode.

 

RUI Type 

(The electrical signal 

type of sensor 

element)

 

 

Press <M> until this page is appeared on LCD. Then press 
<Z> to access the RUI Type (programing mode). You can 
identify  the  electrical  signal  type  of  sensor  element  by 
selecting the resistance type (RES) or voltage type (VOL) 
by pressing <S>. After that, press <Z> until all characters 
blink. Then press <M> for the saving new parameter and 
switching from programing mode to operation mode. 

 

 

 

Содержание HART PTT74-E Series



























Отзывы: