Specific Maintenance Details
FSC Timber
Clean with a stiff brush once per year, especially in more exposed locations, in order to prevent a verdigris type build up on
the timber surface. Ideally this should be completed in early spring. During the cleaning stage, all exposed timber surfaces
should be inspected for splits and splinters. Any splinters and graffiti should be removed and the surface sanded with 100
grit sandpaper in order to remove any uneven / sharp edges or surfaces.
During the first few months after installation the tannin naturally occurring in the timber may leach out and cause a brown
staining on the bases. This may be removed with a light solution of household bleach and water.
Stainless Steel
(polished stainless steel only)
Clean as required, but at least every three months, using a stainless steel polish and a lint free cloth. To remove ground in
dirt, a stainless steel finishing pad may be required.
Polyester Powder Coated & Galvanised
For general cleaning using a damp cloth and warm soapy water only. Scourers and abrasive cleaners are NOT suitable for
these types of finish and may damage them. Before using any cleaning agents to remove graffiti etc. try on a small,
inconspicuous area first to avoid causing more unsightly damage.
Repairs
FSC Timber
For light damage, please see section on specific maintenance details above. For instances of heavy damage, the timber item
should be replaced. Please order against the part number reference in the reordering section towards the end of this manual.
Stainless Steel
Light damage (surface scratches etc.) can be removed using an emery pad (240 grit) and freeing oil such as ‘WD40’. Care
should be taken to follow the direction of the brushing grain. It is recommended that a trial repair be carried out on an
unimportant surface first. No corrosive cleaners or other abrasives should be used. Any contamination, particularly carbon
steel scuffs from vehicles, should be quickly removed to avoid corrosion.
Polyester Powder Coated Surfaces
For light damage (scratches, chips etc.) repair using touch-up paint to match original colour (available from Factory Furniture
Ltd). Paint application should be carried out in accordance with approved methods detailed by the paint manufacturer.
Please note that it is advisable to use professional painters to achieve best results when touching up larger areas. Products
for respraying larger areas are available from Factory Furniture Ltd.
Heavy Damage
In the event of serious damage to any component, replacements should be ordered from Factory Furniture Ltd. In this event
(or if the product needs to be disassembled for any reason), please contact Factory Furniture for detailed technical advice.
Reordering / Spares
Part No.
Item Description
P3009 / 01
1 no. Large Boort bin slat set (30 no. slats total)
P3009 / 02
1 no. Large Boort bin liner
P3009 / 03
1 no. Large Boort bin lid
Instructions For Reordering
If possible, please specify job name or number at the time of reordering to enable identification of details such as the stainless
steel finishes and polyester powder coat colours etc. In any event where either, additional orders are required, or spares and
replacements are required please contact Factory Furniture Ltd. Using the part numbers given above as reference should
help us to process your enquiry more efficiently.
Note - All fittings required to assemble ordered parts will automatically be included in the order.
AutoCAD Drawing List
FF3009 / 01
LARGE BOORT LITTER BIN
GENERAL ARRANGEMENT DRAWING
FF3009 / 02
LARGE BOORT LITTER BIN
BIN PART DETAIL DRAWINGS
FF3009 / 03
LARGE BOORT LITTER BIN
LINER PART DETAIL DRAWINGS
FF3009 / 04
LARGE BOORT LITTER BIN
SETTING OUT DRAWINGS
Contacts
Factory Furniture Ltd, The Stableyard, Coleshill, Swindon. Wiltshire SN6 7PT. U.K.
Tel
+44 (0) 1793 763829
Fax
+44 (0) 1793 861615
Email [email protected]
Web
www.factoryfurniture.co.uk
3
LARGE BOORT BIN Maintenance
