Fabtech FTS21052BK Скачать руководство пользователя

Страница: 1 / 10

www.fabtechmotorsports.com

4331 EUCALYPTUS AVE. CHINO, CA. 91710

PHONE 909-597-7800 FAX 909-597-7185

2007 - 13 GM 1500 4WD – 2WD SUV REAR SYSTEM

FTS21051BK REAR AUTO RIDE COIL SPRING SYSTEM

FTS21052BK REAR Non /AUTO RIDE COIL SPRING SYSTEM

THIS INSTRUCTION SHEET COVERS THE INSTALLATION OF VEHICLES WITH AND WITHOUT AUTO RIDE

SUSPENSION. VERIFY THAT YOU HAVE THE CORRECT KIT FOR YOUR APPLICATION.

READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION!

CHECK ALL PARTS INCLUDED IN THIS KIT TO THE PARTS LIST ABOVE BEFORE BEGINNING

INSTALLATION OF THE KIT. IF ANY PIECES ARE MISSING, CONTACT FABTECH AT 909-597-7800

VEHICLES THAT WILL RECEIVE OVERSIZED TIRES SHOULD CHECK BALL JOINTS, TIE RODS ENDS AND

IDLER ARM EVERY 2500-5000 MILES FOR WEAR AND REPLACE AS NEEDED.

WARNING:

FABTECH RECOMMENDS THAT YOU EXERCISE EXTREME CAUTION WHEN WORKING

WITH COIL SPRINGS TO AVOID ANY POSSIBILITY OF INJURY.

THIS KIT NOT RECOMMEND FOR 2WD SUBURBAN.

TOOL LIST: (NOT INCLUDED)

FLOOR JACK

JACK STANDS

EXTERNAL COIL SPRING COMPRESSOR

ASSORTED METRIC AND S.A.E SOCKETS, & ALLEN WRENCHES

DRILL WITH 7/16” BIT

DIE GRINDER WITH CUT OFF WHEEL

Содержание FTS21052BK










