Faber e-MatriX 800, Руководство по установке

Страница: 12 / 20

Installation manual e-MatriX 800/1600 ST
12 < < < <
6.2 Pebbles/Acrylic ice
Spread an even amount of Pebbles or Acrylic-ice on
the bottom plate.
Functional test

See “Using the appliance for the first
time” in chapter 4 of the user manual.

Check all connections for water leaks.

Check the operation of the extractor fan.

Check the operation of the heating fan.

Check the operation of the remote control
at the desired distance (max. 8m).

Check the operation of the ITC-V2 App.

Place the decoration set, see chapter 6.

Close the door;

Do a final functional test.
Maintenance
8.1 Maintenance frequency

Cleaning water sump, air filter and replac-
ing the transducer.
Commercial use:
o
Every three months.
Domestic use:
o
Once a year.

Cleaning mesh filter and replacing in-line
filter.
Commercial use:
o
Once a year.
Domestic use:
o
Every second year.

Please note!
The maintenance interval depends on the wa-
ter quality and/or the running hours and
therefore can differ from the above men-
tioned.
Cleaning water sump

Please note!

Always press the mains switch of the Con-
trol box to the OFF (0) position, see fig.
1.3-D and disconnect the power supply,

Never use abrasive cleaners.
1. Open the (service)door, see chapter 5;
2. Remove the decoration set;
3. Lift the bottom plate in the middle and let
it rest carefully at front of the fire. See fig.
1.2;
4. Disconnect the plug connection, pressing
in the plug's locking clip to do so. Remove
the base plate to gain full access to the
engine, see fig. 6.0;
5. Disconnect the “fill cap” by turning it
clockwise, see fig. 6.1.
6. Disconnect the transducer cable, see fig.
6.2.
7. Release the clip on both sides and remove
the nozzle, see fig. 6.3 and 6.4.
8. Without spilling any water, lift up the wa-
ter sump gently and empty the water
sump, see fig. 6.5.
9. The transducer is fixed in the water sump
with a plastic clip. Push the clip backwards
gently and remove the transducer, see fig.
6.6.
10. Put a small amount of washing up liquid
into the water sump and using a soft
brush to clean the sump. Also clean the
transducer, including the disc underneath
the cone. Remove the cone by turning it
clockwise, see fig. 6.7.
11. When cleaned, thoroughly rinse the water
sump with clean water to remove all
traces of washing up liquid.
12. Clean the nozzle (fig. 6.4) with a soft brush
and flush out thoroughly with water.
Reverse the steps above to reassemble.
Cleaning air filter
1. Gently slide the air filter upwards out of
its plastic holder, see fig. 7.0.
2. Gently rinse with water in the sink and dry
with fabric towel before returning.
3. Replace the air filter.
4. Place the decoration set, see chapter 6.
5. Close the door.
Replacing the transducer

Please note!
Press the mains switch of the Control box to
the “OFF” (0) position, see fig. 1.3-D and dis-
connect the power supply.
1. Follow the first 9 steps in section “Clean-
ing water sump” in chapter 8.1 to gain ac-
cess and remove the transducer.
2. Place the new transducer and repeat the
steps above in reverse order.
(Please take note that the transducer ca-
ble will not block the opening of the
cone).
Cleaning mesh filter
1. Turn off the water supply.
2. Close the ball valves.
3. Unscrew the base and clean the filter in-
side.