Fab Fours F2950 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 21

Fab Fours F2950 Скачать руководство пользователя страница 10

Installation Instructions

Dodge 1500 Premium Front Bumper

Product Number: F2950, F2951, F2952

Application: 2013-2018 Dodge 1500

Copyright 2008 Fab Fours, Inc.

Page 10 of 21

F295X_REV_A

III.

Pre-Installation

NOTE:  The  Following  Installation  steps  apply  to  the  installation  of  the
Front  Bumper.  PLEASE  READ  THE  ENTIRE  MANUAL  BEFORE
ATEMPTING  INSTALLATION.  Ignoring  these  steps  will  increase  your
probability of scratching the vehicle during product installation.

A.

Remove the bumper from the shipping carton. Lay all items out on a non-scratch
surface to prevent damage to the powder coating.

B.

For sensor installation run sensor harness under winch tray. Reverse steps J through
M in previous section making sure that the clear plastic grommet is on properly and
sensors appear centered in their housings. Final installation of sensors on driver side
should appear as follows with passenger side sensors mirrored. (Ref. Figures 9a-f)

Figure 9a

«
...
8
9
10
11
12
...
»

Содержание F2950






















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды