manualshive.com logo in svg
background image

7

a

b

c

ENGLISH

4  MANUAL OPERATION

OPEN

CLOSED

UNLOCKED

LOCKED

Fig. 18

5  ELECTRICAL CONNECTION OF THE "2easy bus" ENCODER

The S450H operator is fitted with an encoder system with "2easy bus" technology. The proper assignment of the leaf to the corresponding 
encoder depends on the connection of the two encoder wires (leaf 1- encoder 1; leaf 2 - encoder 2).    
THE ENCODER WIRES MUST BE CONNECTED TO THE "2easy bus" CONNECTOR OF THE ELECTRONIC EQUIPMENT.
To verify the proper combination

 LEAF  - ENCODER  - MOTOR 

 and 

LEAF 2 - ENCODER 2 - MOTOR 2

, refer to the LEDs on the 

encoders, as shown by table 2 and the figures 19 - 20 - 21.

To invert the leaf-encoder combination, change the encoder polarity by swapping its wires until the right LEDs are lit.

TABLE 2

LED

ON

BLINKING

OFF

DL 

Power supply ON and BUS - board 

communication

Power supply ON but

 no BUS communication

(e.g.: cabling fault)

Power supply OFF and no BUS communi-

cation

(e.g.: missing or broken connection)

DL 2

Encoder associated to leaf 

/

Encoder associated to leaf 2

DL 

/

Pulse reading during leaf movement

Leaf stationary

DL 

must always be ON

 to ensure the right connection between encoder and board.

DL 2:  indicates the leaf where the encoder is installed.

If the encoder is installed on leaf 1, the DL 2 LED is ON.
If the encoder is installed on leaf 2, the DL 2 LED is OFF. 

DL  : 

  when 

blinking

  at  regular  intervals,  it  signals  the  pulse  reading

  during  the  leaf 

movement

When the gate leaf is stationary, DL  is OFF.

If the gate is to be operated manually because of a power failure or an automated system fault, activate the release device.  
1) Lift the protection lid (Fig. 18, re. 

a

) and insert the key in the lock (Fig. 18, ref. 

b

).

2) Turn the key 90° clockwise to open the cover and lift it.

) Turn the release knob (Fig. 8, re.

 c

) anticlockwise until it stops.

4) Open or close the leaf manually.
To restore the normal operation of the automated system, perform the above described operations in reverse order. 

  The LEDs of the encoder remain visible also with the protection cover of the rear 

bracket installed.

   

The models S450H SB are not equipped with a release facility since, thanks to the particular configuration of the hydraulic 

distributing flange, you do not need to release the operator to manually move the leaf

Содержание S450H












Отзывы: