FAAC DAAB EP104 Скачать руководство пользователя

Страница: 20 / 74

Instruction manual version 1 for software version 4.04

INSTRUCTION MANUAL FOR DAAB EP104 CONTROL BOARD

Commissioning

The process is the same for EP104-1 for one motor winder and EP104-2 for two motor winders.

The settings are changed as described in the section "Changing settings in the EP104".

An E on the far left of the display indicates an error message, see "Error messages". Note that the start-up values "EP-1" and

"EP-2" are not error messages.

Carry out the commissioning steps in the order shown – this will ensure that the channels are configured in the correct

sequence.

The automatic control unit is supplied in hold-to-run mode. Hold-to-run means that the motor runs while the button is

pressed, and stops when it is released.

The control unit will only work correctly if the following steps are carried out:

• Safety

Anyone commissioning the EP104 must have documented knowledge and understanding of its functions, and knowledge

of commissioning control systems for the application to be used.

See "Settings" to find out how to read and configure values in the EP104.

Check that:

• All equipment is mechanically secure and installed according to the applicable instruction manuals.

• All components are correctly connected and installed by authorised installers before switching on the power supply.

• The necessary safety measures are in place to remove the risk of crushing and other risks relating to the controlled unit.

• Any necessary decoupling devices are installed in the controlled unit and that they work as intended.
Make sure you:
• Discharge any static charge in your body by touching an earthed object, for example the earth connection between the door

and the control unit, before changing settings or doing other work on the EP104.

• Take care when operating internal buttons to avoid touching live components.

• Stop circuit

The stop circuit consists of a safety output, stop buttons and contactors. If the control unit detects a fault during the self test,

the power to the contractors is interrupted. The stop buttons are connected in series with the contactors, and they interrupt

the power to the contactors. Check that the stop diode lights up.

• Limit switch

Limit switches are used to inform the unit when the door is in the open or closed position. There are three limit switch options

to choose from: encoders, which are electronic limit switches that detect the exact position of the door in degrees; mechanical

limit switches using ridges that control microswitches; or, if the motor does not have any limit switches, timer control.

Encoder (electronic limit switch)

Right/left encoder position

The encoder works by detecting the position of the door, and acts as an intelligent limit switch. A magnetic sensor means

that the EP104 knows the precise position of the door, and the limits for the open and closed positions can be directly

configured in the unit using degrees, rather than physically changing the limit switch ridges in the motor winder. It is

possible to commission one half at a time by activating only one limit switch at a time (L001, L002).

For a top-mounted motor winder, the motor is configured as for a right-mounted motor window. See below for the side-

mounted motor winder. Note that if the motor winder is installed upside down, the sides must be swapped because the

motor runs in the "wrong" direction.

•

Connect the encoder according to the instructions on page 15, "Connecting an encoder".

•

Specify that the encoder is used for motor 1 by setting L001 to 1, specify the position of the motor 1 in channel

L110 – 1 is left and 2 is right.

•

If two motor winders are used, activate the encoder for motor 2 in channel L002 by setting it to one 1, specify the

position of motor 2 in channel L120 – 1 is left and 2 is right.

•

After setting the encoder position and activating it, run the motor (hold-to-run) to the closed position, then read

channel L111 for motor 1 and make a note of the value. If two motor winders are used, also read channel L121 and

make a note of the value. This value must always decrease when closing and increase when opening.

Left

Right

Содержание DAAB EP104











































































Результаты поиска

Содержание DAAB EP104

Отзывы:

Похожие инструкции для DAAB EP104

Бренды по названию

Популярные бренды

FAAC DAAB EP104, Инструкция по эксплуатации

Результаты поиска

Содержание DAAB EP104

Отзывы:

Похожие инструкции для DAAB EP104

Бренды по названию

Популярные бренды