![background image](http://html.mh-extra.com/html/faac/d600/d600_instruction-manual_535498034.webp)
15
ENGLISH
4) Within these 5 secs., press the appropriate push-button on
the LC remote control.
5) The LED lights up on steady beam for 1 second, indicating
memory storage executed, and then resumes flashing for
another 5 sec., during which another radio control (point 4)
can be memory stored.
6) When the 5 secs. have elapsed, the LED goes OFF indicating
the end of the procedure.
7) To add other radio controls, repeat the operation from point
1).
12.3.1 Remote memory storage of LC radio controls
Other radio controls can be remotely stored only with the LC
radio controls, i.e. without using the RADIO SETUP
push-buttons, but using a previously stored radio control.
1) Obtain a radio control already stored on one of the 2
channels (OPEN A or OPEN B).
2) Press and simultaneously hold down push-buttons P1 and P2
until the lights of both the LEDs on the board light up.
3) Both LEDs flash slowly for 5 sec.
4) Within 5 sec. press the push-button of the radio control that
had been memory stored to enable learning on the selected
channel (OPEN A or OPEN B).
5) The LED on the board relating to the channel being learned
flashes for 5 sec., within which time the code of another radio
control must be transmitted.
6) The LED lights up on steady beam for 2 seconds, indicating
memory storage executed, and then resumes flashing for 5
sec., during which other radio controls can be memory stored,
as in point 5, and then goes OFF.
12.4 Radio controls deletion procedure
1) To delete
ALL
the radio control codes, hold down push-button
OPEN A or OPEN B for 10 sec.
2) The LED relating to the pressed push-button flashes for the first
5 sec, and then flashes more quickly for the next 5 sec.
3) Both LEDs light up on steady beam for 2 sec and then go
OFF.
4) Release the pressed push-button when both LEDs light up on
a steady beam.
This operation is NOT reversible.
All codes of radio controls stored as OPEN A and OPEN
B will be deleted.
13 START-UP
After installation, make sure that no part of the door
interferes with public spaces such as pavements and/or
roads.
Check the status of the unit’s inputs and make sure that all the
safety devices are correctly connected (the relevant LEDs must
be lighted).
Run a few complete cycles to check if the automated system
and the accessories connected to it are operating correctly,
addressing special care to the safety devices and the
anti-crushing device of the operator. Check if the automated
system is able to detect an obstacle with a height of 50mm
laid on the ground.
Apply the stickers indicating the release manoeuvre near the
automated system. Apply the danger signal sticker (Fig. 32), so
that it is clearly visible, near to the door or near to the control
device.
Hand the customer the page entitled “User’s guide”, and
Fig. 33
Fig. 32
describe how the system works, and the operator release and
locking operations indicated in the guide.
14 PARACHUTE CABLES
Connect the parachute cables to the rear door and to the
ceiling lamp to prevent accidental falls (Fig. 33).
15 MAINTENANCE
Run a functional check of the system at least every 6 months,
with special attention to the efficiency of the safety and release
devices.
Once a month: check the efficiency of the anti-crushing device
and also check if it is able to detect a 50mm high obstacle laid
on the ground.
16
REPAIRS
For repairs, contact FAAC’s authorised Repair Centres.
Содержание D600
