FAAC 950N Скачать руководство пользователя страница 20

Страница: 20 / 30

950N 19

732708

- Rev. F

ENGLISH

SW1= SET-UP START BUTTON

ALIANO

950 O/I BOARD CONNECTORS

Secondary for transformer

Rapid connector for Manual/Night, Open, Automatic mode selector switch

Connector for KP CONTROLLER programming unit

Common contact for electric lock

Normally open contact for activating the electric lock (max contact capacity 0.5A 24V). The contact

will close following an open command, during the approximately 70° stroke and with the door in ma-

nual mode.

Normally closed contact for activating the electric lock (max contact capacity 0.5A 24V). The contact

will open following an open command, during the approximately 70° stroke and with the door in ma-

nual mode.

Door closed status (normally open contact, max 0.5A / 24V ).

The contact will close when the door is closed.

Common contact for door status

Door open status (normally open contact, max 0.5A / 24V ). The contact will close when the door is

opened.

7-8

GND = control board power supply negative

+ 24 V= control board power supply positive

Internal open command (normally open contact).

In night mode does not open door.

External open command (normally open contact).

In night mode does not open door.

Emergency command (normally closed contact). If open, it commands door closing (the mode can be

modified using the KP controller)

Safety command during closing phase (normally closed contact). If open during closing, it reverses

the opening motion. As long as it is open it inhibits closing.

Opening STOP safety device command. If open, it blocks the motion and restores it when it is no

longer engaged. As long as it is open, it inhibits the opening (normally closed contact)

Key command (normally open contact).

If closed, it commands door opening in any mode.

Fire alarm command (normally open contact).

If closed, it commands door closing.

Command coming from the card reader positive (24V signal = between 17 and 18).

The pause time is fixed on 10 seconds.

18-19

GND = control board power supply negative

Exchanging relay - Common contact

Exchanging relay - (normally open contact). This output closes when the card reader input

is activated, for 2 seconds.

Exchanging relay - (normally closed contact). This output opens when the card reader input

is activated, for 2 seconds.

Board fault output - Common contact

Board fault output (normally open contact).

This output closes when there is a board fault (see section 11.3)

+24 V=

GND = control board power supply negative

Interlock output if dip 9 = OFF

Failsafe output for sensor monitoring if dip 9 = ON

“Two leaf” output

Terminal for interrupting motor power (if interrupted, it cuts off power to the motor)

Содержание 950N































Результаты поиска

Содержание 950N

Отзывы:

Похожие инструкции для 950N

Бренды по названию

Популярные бренды

FAAC 950N, Руководство пользователя

Результаты поиска

Содержание 950N

Отзывы:

Похожие инструкции для 950N

Бренды по названию

Популярные бренды