manualshive.com logo in svg

F.W. Bell 5060, Инструкция по эксплуатации

Поделиться
Скачать
F.W. Bell 5060 Скачать руководство пользователя страница 38

 

4-1

 

WARRANTY 

This instrument  is warranted to be free of defects in material and workmanship.  
Sypris Test & Measurement’s obligation under this warranty is limited to servicing 
or adjusting any instrument returned to the factory for that purpose, and to 
replace any defective parts thereof.  This warranty covers instruments which, 
within one year after delivery to the original purchaser, shall be returned with 
transportation charges prepaid by the original purchaser, and which upon 
examination shall disclose to Sypris Test & Measurement’s satisfaction to be 
defective.  If it is determined that the defect has been caused by misuse or 
abnormal conditions of operation, repairs will be billed at cost after submitting an 
estimate to the purchaser. 
 
Sypris Test & Measurement reserves the right to make changes in design at any 
time without incurring any obligation to install same on units previously 
purchased.  
 
THE ABOVE WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER 
WARRANTIES EXPRESSED OR IMPLIED AND ALL OTHER OBLIGATIONS 
AND LIABILITIES ON THE PART OF SYPRIS TEST & MEASUREMENT, AND 
NO PERSON INCLUDING ANY DISTRIBUTOR, AGENT OR 
REPRESENTATIVE OF SYPRIS TEST & MEASUREMENT IS AUTHORIZED 
TO ASSUME FOR  SYPRIS TEST & MEASUREMENT ANY LIABILITY ON ITS 
BEHALF OR ITS NAME, EXCEPT TO REFER THE PURCHASER TO THIS 
WARRANTY.  THE ABOVE EXPRESS WARRANTY IS THE ONLY WARRANTY 
MADE BY  SYPRIS TEST & MEASUREMENT.  SYPRIS TEST & 
MEASUREMENT DOES NOT MAKE AND EXPRESSLY DISCLAIMS ANY 
OTHER WARRANTIES, EITHER EXPRESSED OR IMPLIED, INCLUDING 
WITHOUT LIMITING THE FOREGOING, WARRANTIES OF 
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR 
ARISING BY STATUE OR OTHERWISE IN LAW OR FROM A COURSE OF  
DEALING OR USAGE OR TRADE.  THE EXPRESS WARRANTY STATED 
ABOVE IS MADE IN LIEU OF ALL LIABILITIES FOR DAMAGES, INCLUDING 
BUT NOT LIMITED TO CONSEQUENTIAL DAMAGES, LOST PROFITS OR 
THE LIKE ARISING OUT OF OR IN CONNECTION WITH THE SALE, 
DELIVERY, USE OR PERFORMANCE OF THE GOODS.  IN NO EVENT WILL 
SYPRIS TEST & MEASUREMENT BE LIABLE FOR SPECIAL, INDIRECT OR 
CONSEQUENTIAL DAMAGES EVEN IF SYPRIS TEST & MEASUREMENT 
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. 
 
This warranty gives you specific legal rights, and you may also have other rights 
that vary from state to state. 
 
 

Содержание 5060













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды