F.F. Group CS 55/1200 PLUS, Оригинальное руководство пользователя

Страница: 6 / 40

| English 6
Functional Description:
1. Lever of lower guard
2. Dust extraction outlet
3. Saw blade
4. Power-on indicator
5. Auxiliary handle
6. Carbon brush cover
7. Angle gauge
8. Lock knob for angle adjustment
9. Lock knob for edge guide
10. Baseplate
11. Edge guide
12. Outer flange
13. Blade clamp bolt
14. Lower guard
15. Spindle lock button
16. ON/OFF switch
17. Lock-off button
18. Main handle
19. Depth gauge
20. Lock lever for depth adjustment
ASSEMBLY
Important: Prior to any assembly and adjustment
always unplug the tool.
Changing the blade (image 3&4)
Warning: Always disconnect the plug from the
power source before making any adjustment or at-
taching any accessories. Do not to use any abrasive
wheels.
1. Place this circular saw on its side on a flat surface.
Advice you bring the base plate down as if a mini-
mum depth cut which is ease to operate.
2. Push the spindle lock button 15 toward motor
housing as the arrow shows in Fig. 3 and firmly
hold it.
3. Turn the blade clamp bolt 13 anti-clockwise by us-
ing the Allen key that supplied with the tool.
4. Remove the blade clamp bolt and outer flange 12 .
5. Raise the lower guard 14 by using the lever for
lower guard 1 , and then remove the saw blade.
6. Clean the saw blade flanges, then mount the new
saw blade onto the output spindle and against
the inner flange.
7. Make sure the saw teeth and arrow on the blade is
to be the same direction as the arrow on the lower
guard.
8. Reinstall the outer flange, and tighten the blade
clamp bolt.
9. Make sure that the saw blade runs freely by turn-
ing the blade by hand.
Depth adjustment (image 5)
1. Loosen the lock lever for depth adjustment 20 .
2. Hold the baseplate flat against the edge of the
work piece and lift the body of the saw until the
blade is at the right depth determined by the
depth gauge 19 (align the scale line).
3. Tighten the lock lever for depth adjustment.
Angle adjustment (image 6)
1. Loosen the Lock knob for angle adjustment 8 .
2. Adjust the shoe to the desired angle between 0° to
45° [See Angle gauge 7 ].
3. Tighten the lock knob for angle adjustment.
Switch on and off (image 7)
Before engage the ON/OFF switch, check that
the saw blade is properly fitted and run smooth -
ly, the blade clamp screw is well tightened.
1. Connect the plug to the power supply, the pow-
er-on indicator 4 is illumed until the tool discon-
nect from the power mains.
2. To switch on the circular saw, press the lock-off
button 17 and pull the ON/OFF switch trigger 16 .
3. When you release the switch trigger 16 , the tool
turns off.
Parallel cut adjustment (image 8)
1. Loosen the lock knob of edge guide 9 .
2. Slide the edge guide 11 through the slots in the
shoe to the desired width.
3. Tighten the lock bolt to secure it in the position.
4. Ensure that the edge guide rests against the
wood along its entire length to give a consistent
parallel cuts.
Replacement of the Carbon Brushes (image 9)
For safety reasons, the machine automatically switch-
es off if the carbon brushes are so worn out that they
no longer have contact with the motor. In that case,
the carbon brushes must be replaced by a pair similar
carbon brush available through the after-sales service
organization or qualified professional person. Loosen
the carbon brush cover anti-clockwise with using a
screwdriver, open the cover and remove the carbon
brushes. If they are 6 mm or less then they must both
be replaced. Fit new carbon brushes and replace the
brush housing.
CAUTION: The brushes must always be replaced in
pairs.
CAUTION: Always disconnect the machine from the
power supply before removing any electrical covers.
OPERATION
General cut
1. When starting, always hold the saw handle with
one hand and the auxiliary handle 5 with the oth-
er hand. Never force the saw but maintain a light
and continuous pressure after completing the cut
allow the saw to come to a complete stop. When
cutting is interrupted, resume cutting by allowing
the blade to reach full speed and then reentering
the cut slowly.
2. When cutting across the grain, the fibers of the
wood have a tendency to lift and tear, moving the
saw slowly minimizes this effect.
Pocket cut
1. Disconnect the plug from the power supply
before making any adjustments. Set the depth
adjustment based on the thickness of the line
drawing for the cut. Raise the lower guard by
using the lift lever.
Vibration total values:
a
h
m/s
2
4,75
K m/s 2 1,5