F.F. Group CHD 12V PLUS, Оригинальное руководство пользователя

Страница: 9 / 64

CHD 12V PLUS English | 9
www.ffgroup-tools.com
BASIC CORDLESS ROTARY DRILL OPERA -
TIONS
BATTERY CHARGING
Check the mains voltage. Make sure the voltage
of the power source is the same as the voltage
specified on the rating plate of the charger unit.
Plug your mains plug into the power source. The
green LED indicator 11.2 will blink indicating
stand-by mode. Insert battery pack into battery
compartment of the charger. The red LED indica-
tor will light solid. This indicates that the battery
pack is being fast charged automatically. When
the battery pack is fully charged, the red LED
indicator will turn off and the green LED will illu -
minate solid. Remove the battery pack from the
charger and unplug.
IMPORTANT CHARGING NOTES: Longest life
and best performance can be obtained if the
battery pack is charged when the surrounding air
temperature is between 18°C and 24°C. DO NOT
charge battery pack in an air temperature below
4.5°C, or above 40.5°C. This is important and will
prevent serious damage to the battery pack. The
charger is designed to fast charge the battery
pack between 0°C and 45°C. If the battery pack,
when inserted, is too cold or too hot, the charger
will not charge. The green LED and the red LED
will blink alternatively and continuously to indi -
cate this situation. Once the air temperature is
within tolerance, the fast charging will begin.
CHARGER LIGHT INDICATOR
LED INDICATOR
SITUATION
Green Red
Blinking light No Light Stand by
No Light Solid Light Charging
Solid Light No light Charging is
complete
Blinking light Blinking light Battery pack is
too hot or cold
(charging will begin
automatically when
battery reaches cor-
rect charging tem-
perature)
No light Blinking light Damaged or
faulty battery
pack
DUST AND SWARF
A correctly fitted dust mask, suitable for the ac -
tivity and in accordance to the relevant standard
must be worn. Swarf produced by metal drilling is
extremely sharp. Take precautions when clearing
swarf. The burr left on the hole is also sharp and
should be removed with a suitable tool. Always
wear safety goggles.
WARNING: Drill bit will be hot after use.
INSTALLING AND REMOVING BITS
The drill is fitted with a keyless chuck, this means
that a chuck key is not required to secure the drill
or screwdriver bit.
i. Place the drill bit shoulder into the chuck as far
as it will go.
ii. Tighten the chuck firmly.
Note: Short screwdriver bits need only be insert-
ed to the depth of the hexagon shank before
tightening chuck by hand.
LED WORK LIGHT
To aid drilling and screwdriving in confined, inade -
quately lit spaces, the LED work light (7) automat-
ically illuminates when the trigger is activated .
FORWARD/REVERSE SELECTOR
The switch determines the direction of rotation
of the chuck, i.e. clockwise or anticlockwise.
i. Stop the drill and push switch (2) to the left
or right. NOTE: When the direction switch is
pushed to the left, the chuck will rotate clock -
wise. Before operation, check that the switch
is set in the required position. Do not change
the direction of rotation until the chuck
comes to a complete stop.
ii. When the drill is not in use move the direction
switch to the neutral position (the middle set-
ting) to lock the trigger out.
TRIGGER
When the trigger is depressed, the chuck will ro -
tate (provided the direction switch is set in the
forward or reverse position). This trigger switch
is electronic which enables the user to vary the
speed continuously. The speed varies according
to how far the trigger switch is depressed. The
further it is depressed, the faster the chuck will
rotate. The lighter it is depressed, the slower it
will rotate.
TORQUE SELECTION CONTROL
By turning the collar (4) it is possible to adjust the
amount of torque. Settings 1-21 provide a facil-
ity for setting the torque to the required level.
For example, this means that repetitive driving
of screws of the same size will be driven into the
material to the same torque, thus giving the same
fixing strength, or in the case of countersunk
screws, these will all be driven to the same depth
in the material. The torque control prevents the
heads of small diameter screws being twisted off
when correctly set. By turning the collar (5) it is
possible to switch between rotary drilling, per-
cussion drilling and screwdriving functions. Set
the "twist drill" setting , for rotary drilling/
screwdriving, in the "hammer drill" setting ,
the percussion feature will come into action. This
is intented for drilling into masonry, etc. Turn the
collar to the setting to use the drill for screw-
driving.
TWO SPEED GEAR BOX
Select a low gear (1) (slower rotational speed and