background image

23

22

Installation

Installation

Chapter 

3

Product Installation Drawing

Installation method and height of household unitautomatically.

Household unit/Interphone

1. Select a place to install the product.

(Install the product and place the center of the
household unit or interphone at a height of 145
cm from the floor.)

2. Fix the wall mount bracket on the selected

place with 2 screws.

3. Connect the wires of the door camera and

interphone (optional) to the household unit
terminal.

4. After mounting the household unit or

interphone on the bracket, secure it with
screws on the bottom of the household unit.

5. Connect the power cord or AC Adaptor(only

for SHT-3305XM/AU).

6. Turn on the power switch on the bottom of the

product and make sure that the power is
applied.

Be careful of electric shock and fire when connecting AC

power or AC Adaptor(only for SHT-3305XM/AU).

Be sure turn on the power switch after connecting the

power cord or AC Adaptor(only for SHT-3305XM/AU).

only for SHT-3305XM/AU

only for SHT-3305XM/AU

Warning

How to install

INTERPHONE

Camera Installation Drawing

Installation method and height of door camera

Door Camera

How to install

1. Select a place to install the product.

(Install the door camera and place the center of the camera at a height of 145 cm from the floor.)

2. Fix the wall mount bracket on the selected place with 2 screws.

3. Connect the connection wire of the household unit to the door camera terminal.

4. Check that the household unit can be called.

Cautions for installation

1. Avoid the direct sunlight, or a place where rainwater spatters, or it is near chemicals and high voltage 

power lines.

2. Do not install in a place with too high or too low temperatures if possible.

SHT-CP601EN, SHT-CP611/EN, SHT-CP611E/EN

Содержание SHT-330XM/EN




















Отзывы: