Ezgo ST 400 48V, Руководство пользователя и сервисное руководство

Страница: 19 / 55

OPERATION AND SERVICE INFORMATION
Page 4
Owner’s Manual and Service Guide
Read all of Manual to become thoroughly familiar with this vehicle. Pay particular attention to all Notes, Cautions and Warnings
Depressing the accelerator pedal will release the park
brake if it is engaged. This is a feature to assure the vehi-
cle is not driven with the park brake engaged. Depress-
ing the accelerator pedal is
not
the preferred method of
releasing the park brake.
Depressing the lower section of the brake pedal is the pre-
ferred method of releasing the park brake to assure the longest
service life of brake components.
COMBINATION SERVICE BRAKE AND PARK
BRAKE PEDAL
The brake pedal incorporates a park brake feature (Ref
Fig. 6 on page 3). To engage, push down on the upper
section of the pedal until it locks in place. The park brake
will release when the service brake pedal is depressed.
Use the lower section of the brake pedal to operate the
service brake system.
RUN - TOW/MAINTENANCE SWITCH
(PDS VEHICLES ONLY)
To reduce the possibility of severe injury or
death resulting from loss of vehicle control,
consider the grade of the terrain the vehicle is
on and set vehicle’s park brake accordingly
before switching the Run - Tow/Maintenance
switch to the ‘Tow/Maintenance’ position. When
in the ‘Tow/Maintenance’ position, the Anti-Roll
Back and Walk-Away safety features of the
PDS system no longer function.
Before attempting to tow vehicle, move the Run-Tow/
Maintenance switch to the ‘Tow/Maintenance’ position.
Failure to do so will damage the controller or motor.
Before disconnecting or connecting a battery, or any oth-
er wiring, move the Run-Tow/Maintenance switch to the
‘Tow/Maintenance’ position.
After connecting a battery, or any other wiring, wait a
minimum of 30 seconds before moving the Run-Tow/
Maintenance switch to the ‘Run’ position.
The PDS vehicle is equipped with a two position switch
located under the passenger side of the seat on the con-
troller environmental cover (Ref Fig. 7 on page 4).
Fig. 7 Run-Tow/Maintenance Switch
With the switch in ‘TOW/MAINTENANCE’ position:
•
the controller is deactivated
•
the electronic braking system is deactivated which
allows the vehicle to be towed or roll freely
•
the warning beeper is deactivated
With the switch in ‘RUN’ position:
•
the controller is activated
•
the electronic braking system and warning beeper
features are activated
PDS vehicles operate only in the ‘RUN’ position.
The PDS is a low power consumption unit but it will drain
the vehicle batteries over a period of time. If the vehicle
is to be stored for a prolonged period of time, the PDS
should be disconnected from the batteries. (Refer to Pro-
longed Storage on page 21)
PLASTIC LOADBED
The manual lift bed is the standard bed for the vehicle.
The bed may be equipped with an optional electric lift
switch.
Failure to follow these instructions may result in
personal injury, damage the vehicle and/or
cause the vehicle to tip over. Operate the vehi-
cle with awareness of the load. Read, under-
stand and follow the Danger label affixed to the
front of the loadbed.
Do not permit anyone to ride in the bed.
TOWING
MAINTENANCE
Always select 'TOW / MAINTEN
ANCE' posit
ion before towing.
After reconnecting batteries, allow a mini
mum of 30 seconds
before select
ing 'RUN' position
To disable electrical system
place switch in 'TOW/MAI
NTENANCE'
position and remove battery wire.
Possibility of electrical arc and battery explosion.
Before removing/connect
ing batteries or electrical
components
turn switch to 'TOW/MAINTEN
ANCE' position.
RUN
TOW
MAINTENANCE
WARNING
l
73340G01