manualshive.com logo in svg

EZG 38 Special Pump, Руководство пользователя

Поделиться
Скачать
EZG 38 Special Pump Скачать руководство пользователя страница 19

Section 4 – Machine operation 

Ensure that the unit is clear of bystanders and other possible hazards before starting. 

Startup 

Place the engine choke lever in the “ON” position. 

Choke is not required for a warm engine.

Note

 - slide lever to the right to operate or close the choke. Slide to the left to stop or open the choke. 

Throttle / accelerator lever  

Ignition / starting key 

•

Slide the throttle lever to the right to the slowest position. Start the engine using the ignition starter

key. Once running, progressively open the choke lever by sliding to the left until the engine runs

without hesitation. Let the engine warm up for a few minutes.

•

For troubleshooting the engine start up, refer to the engine user manual supplied.

Shut Down 

When shutting down, move the switch on the pump control panel to the middle “off” position then 

slow the engine to idle using the throttle lever sliding to the right. Leave the engine idle for a few 

minutes prior to turning off using the ignition key set to the “off” position. 

OPERATIONS

EZG Manufacturing                    1-800-417-9272

                    www.ezgmfg.com

Rev000           5/24/2022            19

Содержание 38 Special Pump





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды