EZ-ACCESS PATHWAY 3G SS06VP Скачать руководство пользователя страница 71

Страница: 71 / 74

Page 71 of 74

7.8.4.

Remove gravity latch and finger catch from bag.

IMPORTANT!

Discard the screws included in the same bag as the gravity

latch and finger catch, as they will not be used. Instead, use the screws

included in the separate hardware bag for the following steps.

7.8.5.

Center finger catch on the gate square tube opposite the hinge and mark center

of holes with a pencil. Drill three 1/8

″

holes through one side of the vertical

handrail tube (FIG. 7.17).

7.8.6.

Use 1/4" nut driver to secure catch with screws (FIG. 7.18).

FIG. 7.17

FIG. 7.18

7.8.7.

Clip the latch to the finger catch and center on the step or ramp vertical square

tube. Mark center of the holes with pencil. Drill four 1/8

″

holes through one side

of the vertical handrail tube (FIG. 7.19).

7.8.8.

Use 1/4

″

nut driver to secure latch using screws. (FIG. 7.20).

FIG. 7.19

FIG. 7.20

DRILL 5/16″ HOLES

WARNING

INSTALL BOLT FROM
THIS SIDE

8 X 1/2″ LONG HEX

WASHER HEAD SCREW

CENTER ON POST

#8 X 1/2″ LONG HEX

WASHER HEAD SCREW

DRILL 1/8″ HOLES

Содержание PATHWAY 3G SS06VP











































































Результаты поиска

Содержание PATHWAY 3G SS06VP

Отзывы:

Похожие инструкции для PATHWAY 3G SS06VP

Бренды по названию

Популярные бренды

EZ-ACCESS PATHWAY 3G SS06VP, Инструкция по сборке

Результаты поиска

Содержание PATHWAY 3G SS06VP

Отзывы:

Похожие инструкции для PATHWAY 3G SS06VP

Бренды по названию

Популярные бренды