manualshive.com logo in svg

Extron electronics UCS FT 901, Руководство пользователя

Поделиться
Скачать
Extron electronics UCS FT 901 Скачать руководство пользователя страница 4

 

4

UCS FT 901 and FR 902 • User Guide (Continued)

Cabling and Setup

Figure 4 shows connections for the UCS FT 901 and UCS FR 902.

POWER

12V   

HOST

USB-C

SS 5G

Tx

OUTPUT

Rx

1

2

4

POWER
12V

1.0A MAX

INPU

T

OUTPUTS

1

2

4

POWER
12V

1.0A MAX

INPU

T

O

UTPUT

S

POWER

12V   

DEVICES

INPUT

Tx

1

Rx

2

1.5 A

1.6A MAX

Ground

+12 VDC input

G

External Power Supply

(12 VDC, 2.0 A max.)

Ground all

Devices

Ground

+12 VDC input

G

External Power Supply

(12 VDC, 0.5 A max.)

Ground all

Devices

0.1A MAX

USB

USB Camera

Receiver

USB

Laptop

5

5

5

3

3

3

6

6

6

5

5

5

Transmitter

Multimode Fiber Optic Cable

Compatible with USB 3.2, 2.0, 1.1
peripheral devices

1

1

1

2

2

2

3

3

3

4

4

4

Compatible with USB 3.2
host ports ONLY

Figure 4. 

Transmitter and Receiver Connection with Two External Power Supplies

Installation Procedure

ATTENTION:

 

• 

Installation and service must be performed by authorized personnel only.

• 

L’installation et l’entretien doivent être effectués uniquement par un technicien qualifié.

To ensure proper operation, the transmitter, receiver, USB host, and USB peripherals must be connected properly and in the 
sequence described here (see figure 4). 

1. 

Power off all devices that will be directly connected to the receiver.

2. 

Wire each of the two provided power supplies to their 2-pole captive screw connectors (see figure 5).

Captive Screw Connector

Tie Wrap

Heat
Shrink

1/8"

(3 mm)

7/8"

(22 mm)

3/16"

(5 mm) Max.

Figure 5. 

Wiring the Power Connector for the UCS FT 901 and FR 902

NOTE:

  The UCS FT 901 (transmitter) can also be powered by the host device, without the need for the external power 

supply. 

3. 

Plug the two power supply connectors into their respective transmitter or receiver rear panel connectors (see figure 4, 

3

). 

Connect the 6 Watt power supply (

1

) to the transmitter, and the 24 Watt (

2

) to the receiver.

The green Power LED (see 

figure 6

, 

A

, on the next page) on the front panel of each device lights when each device is 

powered on. 

4. 

Connect a USB Type A-to-C or Type C-to-C cable from the host device to the transmitter Host port (

4

). The Host LED 

(

figure 6

, 

B

) will light, indicating that communication between the transmitter and host device has been established.

4 

 

5 

 

Содержание UCS FT 901









Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды