Extron electronics TLI Pro 201 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 46

background image

Configuration
Software

This section of the user guide provides information about:

•

Configuration Software

•

Downloading Software

•

Using the Software

•

TLI Pro 201 Web Page

•

Updating the Firmware

Configuration Software

NOTES:

•

The TLI Pro 201 uses GUI Designer and Global Configurator Plus and
Professional (GCP) to design and configure the graphical user interface.

•

Alternatively, the TLI Pro 201 can use Global Scripter instead of GCP to program
the graphical user interface.

•

The TLI Pro 201 can use Toolbelt to configure network settings.

•

All four software products are available at

www.extron.com

(see “Downloading

Software” below).

Downloading Software

GUI Designer, Global Configurator, Global Scripter, and Toolbelt can be downloaded from

www.extron.com

1.

Click

Download

(see figure 24,

1

) and then click

Software

(

2

).

1

1

1

2

2

2

Figure 24.

Extron Download Page

TLI Pro 201 • Configuration Software

23

«
...
29
30
31
32
33
...
»

Содержание TLI Pro 201















































Отзывы:

Нет отзывов

Похожие инструкции для TLI Pro 201

Бренд: CAME Страницы: 32

ServeRAID M5014

Бренд: IBM Страницы: 106

Бренд: Racal Instruments Страницы: 94

Бренд: Racal Instruments Страницы: 97

Бренд: Uclear Страницы: 40

Бренд: OMA Страницы: 75

Бренд: National Instruments Страницы: 14

Бренд: National Instruments Страницы: 31

Бренд: National Instruments Страницы: 50

Бренд: National Instruments Страницы: 24

Бренд: National Instruments Страницы: 13

Бренд: National Instruments Страницы: 21

Бренд: National Instruments Страницы: 39

Бренд: National Instruments Страницы: 22

Бренд: National Instruments Страницы: 8

Бренд: National Instruments Страницы: 20

Бренд: National Instruments Страницы: 9

FIeldPoint FP-AO-200

Бренд: National Instruments Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды