background image

Result

The unit reverts to factory-installed firmware. Event scripting does not start if the unit is 
powered on in this mode. All user files and settings such as drivers, adjustments, and IP 
settings are maintained.

NOTE:

  To return the unit to the firmware version that was running prior to the reset, cycle 

power to the unit.

Reset All IP Settings

This mode resets all IP settings to factory defaults.

Activation

To reset all IP settings:

1. 

Hold down the 

Reset

 button (see 

figure 2

G

 on page 5) for about 6 seconds until 

the Reset LED (

F

) blinks twice (once at 3 seconds, again at 6 seconds).

2. 

Release and press the 

Reset

 button momentarily (for <1 second) within 1 second. 

Nothing happens if the momentary press does not occur within 1 second.

Result

• 

Resets All IP Settings mode:

• 

Sets the IP address back to factory default (

192.168.254.251

)

• 

Sets the subnet mask back to factory default (

255.255.255.0

)

• 

Sets the gateway address to the factory default (

0.0.0.0

)

• 

Sets all other IP settings, addresses, and domain and host names back to factory default

• 

Turns DHCP off

Reset to Factory Defaults

This mode resets all IP settings and touchpanel settings, including passwords, to factory 
defaults and removes all configurations. It allows you to start over with configuration and 
uploading.

NOTES:

• 

The factory configured passwords for all accounts on this device have been set to the 
device serial number. Passwords can be changed during configuration. They are case 
sensitive.

• 

If the device is reset to default settings, the passwords are reset to the default 
password, which is 

extron

 (for either 

admin

 or 

user

).

Activation

To reset the unit to all factory default settings:

1. 

Hold down the 

Reset

 button for about 9 seconds until the Reset LED blinks three times 

(once at 3 seconds, again at 6 seconds, again at 9 seconds).

2. 

Release and press the 

Reset

 button momentarily (for <1 second) within 1 second. 

Nothing happens if the momentary press does not occur within 1 second.

Result

Reset to Factory Defaults mode performs a complete reset to factory defaults (except the 
firmware).

• 

Does everything Reset All IP Settings mode does.

• 

Removes touchpanel user interface layout and configurations.

• 

Resets all touchpanel settings to factory default. 

 

TLI Pro 101 • Reference Material

31

Содержание TLI Pro 101










































Отзывы: