Extron electronics PowerCage 401, Руководство пользователя

Страница: 13 / 57

Cabling and Testing
Refer to the setup guides and user guides for the models of transmitter and receiver boards
you are installing for details on how to cable and set up each board.
Rear Panel Features
WARNING:
Potential risk of severe injury. Installation and service must be
performed by authorized personnel only.
AVERTISSEMENT : Risque potentiel de blessure grave ou de mort. L’installation
et l’entretien doivent être effectués par le personnel autorisé uniquement.
RS-232
1 2
FOX DT HD
Tx
Rx
SIGNAL
HDCP
Rx G Tx
RS-232
Rx G Tx
Tx
Rx
SIGNAL
HDCP
RS-232
1 2
FOX DT HD
Tx
Rx
SIGNAL
HDCP
Rx G Tx
RS-232
Rx G Tx
Tx
Rx
SIGNAL
HDCP
RS-232
HDMI OUT
1 2
AUDIO OUT AUDIO OUT HDMI OUT HDMI OUT AUDIO OUT AUDIO OUT HDMI OUT HDMI OUT AUDIO OUT AUDIO OUT HDMI OUT
FOX DR HD
Tx
Rx
SIGNAL
HDCP
Rx G Tx
RS-232
Rx G Tx
Tx
Rx
SIGNAL
HDCP
RS-232
HDMI OUT
1 2
AUDIO OUT AUDIO OUT HDMI OUT
FOX DT HD
Tx
Rx
SIGNAL
HDCP
Rx G Tx
RS-232
Rx G Tx
Tx
Rx
SIGNAL
HDCP
RS-232
LAN
Rx
G
Tx REMOT
E
100-240V ~ --A MAX 100-240V ~ --A MAX
50-60 Hz 50-60 Hz
2
RS-232
HDMI
1
AUDIO AUDIO HDMI
FOX DT HD
Tx
Rx
Rx Tx Rx Tx
SIGNAL
HDCP
Rx G Tx
RS-232
Rx G Tx
SIGNAL
HDCP
OPTICAL OPTICAL
INPUTS 2
Tx
Rx
2
RS-232
HDMI
1
AUDIO AUDIO HDMI
FOX DT HD
Tx
Rx
Rx Tx Rx Tx
SIGNAL
HDCP
Rx G Tx
RS-232
Rx G Tx
SIGNAL
HDCP
OPTICAL OPTICAL
INPUTS 2
Tx
Rx
2
RS-232
HDMI
1
AUDIO AUDIO HDMI
FOX DT HD
Tx
Rx
Rx Tx Rx Tx
SIGNAL
HDCP
Rx G Tx
RS-232
Rx G Tx
SIGNAL
HDCP
OPTICAL OPTICAL
INPUTS 2
Tx
Rx
2
RS-232
HDMI
1
AUDIO AUDIO HDMI
FOX DT HD
Tx
Rx
Rx Tx Rx Tx
SIGNAL
HDCP
Rx G Tx
RS-232
Rx G Tx
SIGNAL
HDCP
OPTICAL OPTICAL
INPUTS 2
Tx
Rx
C D E
F A B GH
Figure 2. The Rear Panel of the PowerCage 401 Enclosure
A
Power connector 1 — Connect this port to a 110-240 VAC, 50-60 Hz power source
using a standard IEC power cord.
NOTE: The power supplies and transmitter and receiver boards may be installed or
replaced before or after the unit is powered on.
B
Power connector 2 — Connect this port to a 110-240 VAC, 50-60 Hz power source
using a standard IEC power cord.
C
Slot 1 — Install a PowerCage 401-compatible board into slot 1.
D
Slot 2
— Install a PowerCage 401-compatible board into slot 2.
E
Slot 3 — Install a PowerCage 401-compatible board into slot 3.
F
Slot 4 — Install a PowerCage 401-compatible board into slot 4.
G
LAN connector — Use an RJ-45 cable to attach this connector to a LAN (Ethernet) for
control of the device.
Wire the connector as shown in the image below.
RJ-45
Connector
Insert Twisted
Pair Wires
Pins:
12345678
Straight-through Cable
(for connection to a switch, hub, or router)
End 1 End 2
Pin Wire Color Pin Wire Color
1 white-orange 1 white-orange
2 orange 2 orange
3 white-green 3 white-green
4 blue 4 blue
5 white-blue 5 white-blue
6 green 6 green
7 white-brown 7 white-brown
8 brown 8 brown
Crossover Cable
(for direct connection to a PC)
End 1 End 2
Pin Wire Color Pin Wire Color
1 white-orange 1 white-green
2 orange 2 green
3 white-green 3 white-orange
4 blue 4 blue
5 white-blue 5 white-blue
6 green 6 orange
7 white-brown 7 white-brown
8 brown 8 brown
T568B T568A T568B TIA/EIA-T568B
2
PowerCage 401 Enclosure • Installation 5