Extron electronics MTP C7 T 15HD RS Скачать руководство пользователя страница 18

Use the supplied tie-wrap to strap the power cord to the extended tail of the connector.
As an alternative, an Extron PS 124 Universal 12 VDC Power Supply (part number  

60-1022-01

) can power multiple MTPs or other Extron 12 VDC devices using only one AC 

power connector.

Twisted Pair Cable Termination

Figure 10 details the recommended termination of TP cables with RJ-45 connectors in 
accordance with the TIA/EIA T568A or TIA/EIA T568B wiring standards. You can use either 
standard with CAT 5, 5e, 6, 7, and STP201 cable, but ensure that you 

use the same 

standard on both ends of the cable

RJ-45

Connector

Insert Twisted

Pair Wires

12345678

Pins:

Pin

Signal

1

Red/V. sync +

2

Red/V. sync -

3

Green +

4

Blue/H. sync +

5

Blue/H. sync -

6

Green -

7

Mono audio +

8

Mono audio -

Wire color

White-green

Green
White-orange
Blue
White-blue
Orange
White-brown
Brown

Wire color

TIA/EIA T 568 A TIA/EIA T 568 B

White-orange

Orange
White-green
Blue
White-blue
Green
White-brown
Brown

NOTE:

  When using Enhanced Skew-Free 

  A/V UTP cable, use the 
  TIA/EIA T568A standard only.

Figure 10.

 TP Cable Termination Diagram

NOTES:

 

  RJ-45 termination with CAT 5, 5e, or 6 cable (

for non-C7 units only

) or 

STP201 or CAT 7 cable (for C7 units only) must comply with the  
TIA/EIA T568A or TIA/EIA T568B wiring standards for all connections.

 

  RJ-45 termination with Skew-Free A/V UTP cable (

for non-C7 units only

must comply with TIA/EIA T568A only.

 

  For proper grounding of 

STP201 and CAT 7 cable only

, ensure the shield 

around each wire pair and the shield around the STP201 or CAT 7 cable 
are all tied to the RJ-45 connectors on both ends, in accordance with the 
connector specifications provided by the manufacturer.

 

  Extron Enhanced Skew-Free A/V cable is 

not recommended

 for Ethernet/

LAN applications. This cable is specially designed for compatibility with Extron 
Twisted Pair products that are wired using the TIA/EIA T568A standard.

 

  The green, brown, and blue wire pairs of this cable have virtually identical 

lengths and should be used to transmit the RGB signals.

 

  The orange wire pair of this cable has a different length and 

should not

 be 

used to transmit the RGB signals.

 

MTP 15HD RS Series • Installation and Operation

14

Содержание MTP C7 T 15HD RS



























Отзывы: