background image

MSW 4V SDI rs • Installation and Operation

Installation and Operation, cont’d

2-4

MSW 4V SDI rs • Installation and Operation

 

2-5

Furniture mounting

Furniture mount the MSW using the optional MBU 123 

VersaTools under-desk mounting kit (part #70-212-01) as follows:
1

If necessary, remove the feet from the bottom of the MSW.

2

Attach the mounting brackets to the MSW with the 

provided machine screws (figure 2-3).

 

A/V SWITCHE

R

MODE

NORMAL

AUTO

AUTO

SWITCH

1

2

3

4

Figure 2-3 — Furniture mounting the MSW

3

Hold the MSW with the attached brackets against the 

underside of the table or other furniture.  Mark the location 

of the screw holes of the bracket on the mounting surface.

4

Drill four 3/32" (2 mm) diameter pilot holes, 1/4"  

(6.3 mm) deep in the mounting surface at the marked 

screw locations.

5

Insert #8 wood screws into the four pilot holes.  Tighten 

each screw into the mounting surface until just less than 

1/4" of the screw head protrudes.

6

Align the mounting screws with the slots in the brackets 

and place the MSW against the surface, fitting the screws 

through the bracket slots.

7

Slide the switcher slightly forward or back, then tighten all 

four screws to secure the MSW in place.

Rear Panel Connections

MSW 4V SDI

POWER
12V         

.5A MAX

S

D

I
I

N

P

U

T

S

1

2

3

4

CONTACT 

1 2 3 4

A

B

S

D

I

O

U

T

P

U

T

S

RS-232

Tx Rx

2

5

4

1

3

Figure 2-4 — MSW 4V SDI rs rear panel

a

  SDI Inputs (1 through 4) connectors — Connect up to four  

SDI video sources to these BNC connectors.

b

  SDI Outputs (A and B) connectors — Connect one or two SDI 

display devices to these BNC connectors.  The MSW outputs 

two identical re-clocked SDI signals.

c

  RS-232 connector — Connect a cable with a 3.5 mm, 5-pole 

captive screw connector to this port for bidirectional RS-232 

communication.  Wire the connectors as shown below.

Switcher

PC

Receiv

e

Tr

ansmit Ground

RS-232

Tx Rx

NA

DB9 Pinout (Female)

To control equipment

5

1

9

6

Pin

RS-232

Function

1

2

TX

Transmit data (-)

3

RX

Receive data (+)

4

5

Gnd

Signal ground

6

7

8

9

Figure 2-5 — RS-232 connector wiring

This port has the following RS-232 protocol:
•   9600 baud
•   1 stop bit
•   No parity
•   8 data bits

Содержание MSW 4V SDI rs





















Отзывы: