Extron electronics HSA 800 Скачать руководство пользователя страница 5

Surface Access Products • Introduction

Surface Access Products • Introduction

Introduction

About the HSA Hideaway Enclosures

The Extron Hideaway HSA 800 and HSA 802 are furniture-
mounted, architectural solutions for inconspicuous computer
video interface connector access and control.

The HSA 800 provides space for two double-space (double-
height) or four single-space Extron Architectural Adapter Plates
(AAPs), a standard grounded US, IEC, UK, Europe, or
Australian (depending on the model) AC receptacle, and two
RJ-45 (Category 6) (CAT 6) connectors (figure 1-1).  The HSA 802
provides twice the AAP space with two AC receptacles and four
RJ-45 connectors.

On the US/domestic HSA 802, the AAP spaces, RJ-45
connectors, and AC receptacle are arranged back-to-back on
opposite sides of the enclosure.  On the IEC and all international
versions, the AAP spaces and RJ-45 connectors are also arranged
back-to back, while the AC receptacles are back-to-back on the
sides perpendicular to the AAPs.  Cabling inside the enclosure
runs the AC power line and RJ-45 signal lines from the
connectors on the front panels to connectors on the underside of
the enclosure.

Figure 1-1 — HSA 800 hideaway enclosure

The installed enclosures fit nearly flush within a table or
podium top, storing the AAPs and connectors out of the way
and out of sight.  To access the AAPs and connectors, the user

1-2

presses down on the top of the enclosure, releasing a
mechanical latch.  A gas lift slowly raises the AAPs and
connectors into view.

The functionality of the HSA enclosures can be optimized with
one through four RGB 580

xi

 AAPs connected to one through

four RGB 580

xi

 Remote Interfaces (figure 1-2).

Projector

Extron
HSA 802

Extron
RGB 580

xi 

Mounted
under
a table or 
podium

Mounted

through a table

or podium

SO

G

SER

R

DD

SP

V-

SY

NC

 W

IDT

H

NE

G S

YN

C

CO

MP

 S

YN

C

INP

UT

S

RG

B 5

80

xi

AN

AL

OG

AU

DIO

CO

NT

RO

L

VI

DEO

OU

TP

UT

LE

VE

L

A   

B   

C   

D   

E

PE

AK

ING

HSA 802

H. S

HIFT

COM

PUT

ER

INPU

T

SEL

ECT

AU

DIO

Extron

RGB 580xi

SI AAP

each side

CO

MPU

TER

INP

UT

SEL

ECT

AU

DIO

Figure 1-2 — HSA 802 and RGB 580

xi

xi

xi

xi

xi

 configuration

1-3

im Vertrieb von

            CAMBOARD Electronics

www.camboard.de

Tel. 07131 911201
Fax 07131 911203

[email protected]

Содержание HSA 800


























Отзывы: