Extron electronics EBP 108 RAAP Button Panel, Руководство по установке, Страница: 8 / 10

8
EBP 108 RAAP Button Panel • Setup Guide (Continued)
EBPs that are relatively far from the control processor (see the eBUS Technology Reference Guide at www.extron.com for
details) can be connected to an optional Extron PS 1220EB eBUS power inserter (see figure 7), or an Extron 12 VDC desktop
power supply (see figure 8).
PWR OUT = 6W
V C G
VOL
POWER
12V
1.0A MAX
G Tx Rx RTS CTS
COM 1
3 1 2 4 G
DIGITAL I/O
G Tx Rx
COM 2
-S +V +S G
eBUS
C 1 2
RELAYS
S G
IR/S
LAN
IPCP PRO 250
MAC: 00-05-A6- XX-XX-XX
S/N: ####### E######
Power Input
(100-240 VAC,
50-60 Hz)
ATTENTION:
Do NOT connect the power
pin to any device that is already powered
by the IPCP Pro control processor or by
an additional power supply.
eBUS 24 WATTS MAX
100-240V 50-60Hz
0.6A MAX
-S +V +S G -S +V +S G -S +V +S G
-S +V +S G -S +V +S G -S +V +S G
EBP 108 RAAP
M
S
B
L
S
B
BUS ID
1
ON
2 3 4 5 6
LINK
COM ERROR
ID ERROR
STATUS
RESET
POWER LOAD = 0.5 W
+V +S -S G +V +S -S G +V +S -S G +V +S -S G
eBUS DISTRIBUTION HUB
Ground
+ Signal
+ 12 VDC
- Signal
X
X
Ground
+
Signal
-
Signal
IPCP Pro
Power Input
(100-240 VAC,
50-60 Hz)
PS 1220EB
ATTENTION:
Do NOT connect the power
pin to any device that is already powered
by the IPCP Pro control processor or by
an additional power supply.
3/16"
(5 mm)
Max.
Tie drain wires
to ground.
EBP 108 RAAP
eBUS Connections
• Connect up to five eBUS
endpoint devices to the PS 1220EB.
• Wire the connectors the same at
both ends.
• All ports are identical and
interchangeable.
Figure 7.
Cabling an eBUS System with an PS 1220EB Power Supply and Distribution Hub
+ Signal
- Signal
+ Signal
-
Signal
+
12 VDC
EBP 108 RAAP
M
S
B
L
S
B
BUS ID
1
ON
2 3 4 5 6
LINK
COM ERROR
ID ERROR
STATUS
RESET
POWER LOAD = 0.5 W
+V +S -S G +V +S -S G +V +S -S G +V +S -S G
eBUS DISTRIBUTION HUB
EBP 108 RAAP
M
S
B
L
S
B
BUS ID
1
ON
2 3 4 5 6
LINK
COM ERROR
ID ERROR
STATUS
RESET
POWER LOAD = 0.5 W
+V +S -S G +V +S -S G +V +S -S G +V +S -S G
eBUS DISTRIBUTION HUB
EBP 108 RAAP
PWR OUT = 6W
V C G
VOL
POWER
12V
1.0A MAX
G Tx Rx RTS CTS
COM 1
3 1 2 4 G
DIGITAL I/O
G Tx Rx
COM 2
-S +V +S G
eBUS
C 1 2
RELAYS
S G
IR/S
LAN
IPCP PRO 250
MAC: 00-05-A6- XX-XX-XX
S/N: ####### E######
IPCP Pro
+ Signal
- Signal
+ Signal
-
Signal
+
12 VDC
EBP 108 RAAP
EBP 108 RAAP
Ridged Smooth
3/16" (5 mm) Max.
NOTE: Check the polarity of the power
supply before connecting it to the EBP.
External Power Supply
(12 VDC, 1.5 A max.)
Ground
all Devices
– Return
+12 VDC input
Tie drain wires to ground.
X
X
Ground
Ground
Figure 8.
Cabling EBP Panels with an Extron Power Supply
figure 7